Victron energy Lynx Distributor Скачать руководство пользователя | Manualshive

Страница: 12 / 31

background image

4 batteries in parallel

DC loads

Inverter/charger

Solar charger

Lynx Power In

Lynx Shunt VE.Can

Lynx Distributor

CCGX

VE.Bus

VE.Direct

VE.Can

RJ10 cable

Temp

sensor

System with Lynx Shunt VE.Can, lead acid batteries, a Lynx Shunt VE.Can and a Lynx Distributor

5.1.4. System example - Lynx Smart BMS, 2x Lynx Distributor and lithium batteries

This system contains the following components:

• Lynx Distributor with 2 fused paralleled Lithium Smart batteries with identical cable lengths for each battery (up to 5 paralleled

series strings can be used per system).

• Lynx Smart BMS with BMS, contactor and battery monitor.
• Lynx Distributor provides fused connections for inverter/charger(s), loads and chargers. Additional modules can be added if

more connections are needed.

• A CCGX (or other GX device) to read out the Lynx Smart BMS and Lynx Distributor data.

2 batteries in parallel

DC loads

Inverter/charger

Solar charger

CCGX

VE.Bus

VE.Direct

VE.Can

RJ11 cable

BMS

cables

Lynx Distributor

Lynx Smart BMS

Lynx Distributor

RJ11 cable

System with Lithium batteries, Lynx Smart BMS and two Lynx Distributors

Lynx Distributor

Page 9

System Design

«
...
10
11
12
13
14
...
»

Содержание Lynx Distributor
































Отзывы:

Нет отзывов

Похожие инструкции для Lynx Distributor

ControlMySpa GATEWAY ULTRA

Бренд: Balboa Water Group Страницы: 30

SMTCore Gateway V1

Бренд: IDS Страницы: 4

Бренд: IMMAX Страницы: 3

Бренд: Jasco Страницы: 2

Бренд: LEGRAND Страницы: 2

Бренд: iHome Страницы: 13

Mobile Companion

Бренд: CorAccess Страницы: 9

Core Smart Home Gateway V1

Бренд: IDS Страницы: 53

Бренд: D-Link Страницы: 107

Бренд: MP Solutions Страницы: 2

CORTINO DT72LE Series

Бренд: YOODA Страницы: 5

ActiveHome Pro CM15A

Бренд: X10 Страницы: 25

Бренд: urmet domus Страницы: 36

Kasa Smart EP40

Бренд: TP-Link Страницы: 51

Бренд: Satel Страницы: 8

Бренд: Leviton Страницы: 2

Бренд: Leviton Страницы: 2

Бренд: Leviton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды