Victron energy Lynx Distributor Скачать руководство пользователя | Manualshive

Страница: 26 / 31

background image

Examples of a fuse alarm on the VictronConnect App and on a GX device

Communication lost alarm

This alarm is raised, if a Lynx Distributor was detected by the Lynx Smart BMS on power up but the Lynx Smart BMS cannot see
the Lynx Distributor any longer.

The Distributor status will change from OK to “communication lost” in the VictronConnect App and an alarm message is
displayed. The alarm message will also be shown on a connected GX device and the VRM portal.

NOTE: These alarm codes are a workaround until the Lynx Smart BMS is supported in VenusOS. The alarm message on the GX
device or the VRM portal will be similar to the message shown in the VictronConnect App.

Table 5. Lynx Distributor lost alarm codes

Alarm

Description

#221

Distributor A, communication lost

#222

Distributor B, communication lost

#223

Distributor C, communication lost

#224

Distributor D, communication lost

Lynx Distributor

Page 23

Operation Lynx Distributor

«
...
24
25
26
27
28
...
»

Содержание Lynx Distributor
































Отзывы:

Нет отзывов

Похожие инструкции для Lynx Distributor

ControlMySpa GATEWAY ULTRA

Бренд: Balboa Water Group Страницы: 30

Бренд: Hezborg Страницы: 2

Molekule Air Mini

Бренд: MO Страницы: 24

Бренд: Enerwave Страницы: 2

Moeller Xcomfort CJAU-01/02

Бренд: F&G Страницы: 4

Moeller Xcomfort CRCA-00/01

Бренд: F&G Страницы: 4

Moeller Xcomfort CBEU-02/01

Бренд: F&G Страницы: 4

MOELLER Xcomfort CDAE-01/01

Бренд: F&G Страницы: 4

Бренд: Sonoff Страницы: 43

Designer Roller

Бренд: HunterDouglas Страницы: 32

Бренд: WESTEK Страницы: 2

Бренд: WESTEK Страницы: 12

ALLEGION eFAST MORTICE

Бренд: CISA Страницы: 5

Homelife Smart Plug

Бренд: COX Страницы: 2

Бренд: AIBASE Страницы: 8

Бренд: aqprox! Страницы: 77

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды