INSTALLATION
NSTRUCTIONS
WARRANTY INFORMATION
©
2016
Enerwave Home Automation ●
WWW.
ENERWAVEAUTOMATION
.COM
● CA, USA
Model:
ZW
N-323
M-Plus
Wireless Home Automation Control Device
Plug-in Smart Meter Dimmer Module
020
9
1600
5
1
-01
INSTALLING
Z-WAVE
DEVICES
LOCATIONS
Installation of Z-Wave devices instantly increases the functionality, efficiency, and value of your home. The more devices you install, the more efficient your house will be.
The most effective
locations to install Z-Wave devices are in the Living Room, Bedrooms, Kitchens, Family Rooms, Guest Rooms, and Entertainment Rooms.
This device complies with the Z-Wave standard of open-air, line of sight transmission distances of 100 feet. Actual performance in a home depends on the numbers of walls between the remote
controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in the control network. Z-Wave devices act as signal repeaters ONLY after
they are "Included" on the network.
REQUIREMENTS
This device requires a grounded receptacle. The grounding prong should not be
removed. Doing so is an unsafe practice and will void all Warranties.
Z-Wave devices
require a connection to a compatible hub. Once the device is properly added to the
H
ub, it can be managed and customized to your needs. Please visit
www.enerwaveautomation.com for a list of compatible hubs
.
This device is warranted to be free of material and workmanship defects for 2 years from the date of
purchase. Original receipt or proof of purchase from an authorized retailer must be presented upon warranty
claim. ALL claims must be verified and approved by
Enerwave
, Inc. Warranties from other
Enerwave
products may vary. This warranty is nontransferable and does not cover normal wear and tear or any
malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper
installation. To the fullest extent permitted by the applicable state law,
Enerwave
shall not be liable to the
purchaser or end user customer of
Enerwave
products for direct, indirect, incidental, or consequential
damages even if
Enerwave
has been advised of the possibility of such damages.
Enerwave
’ total liability
under this or any other warranty, express or implied, is limited to repair, replacement or refund. Repair,
replacement or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.
DESCRIPTION
The
ZW
N-323
M-Plus
is a
Dimmer Module with Z-Wave technology
. The
left
receptacle
is "always ON" and the
right
receptacle is Z-Wave controlled. For the advanced users,
the functions are programmable for setting scenes, associations and scheduling
events.
FEATURES
•
Dim lamps and LED lights without the need for wiring
. Plugs into any
Grounded receptacle.
•
Wireless Z-Wave technology creates a mesh network for command and
control interoperability with other Z-Wave compliant controllers and devices
•
Remotely
control of any connected load
•
Manual ON/OFF button conveniently located at the front of the device
•
Reduce energy consumption and enjoy wireless home automation
with Smart
Meter monitoring
•
Over Current and Short Circuit protection up to 15A
SPECIFICATIONS
Voltage.............................................................................................120VAC, 60Hz
Incandescent................................................................................
..
................
30
0W
Z-Wave Frequency.............................................................................. 908.42 MHz
Operating Temperature........................................................................... 32-104° F
FCC COMPLIANCE STATEMENT
FCC Grant of Equipment Authorizations of this device and transmitters installed in this device can be found at FCC website by entering the FCC ID number on the device.
Caution:
C
hanges or modifications not expressly approved by the part responsible for compliance could void the user’s
right
to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation of the device.
T
his equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
WARNING
:
Read and understand these instructions before installing.
Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room than the controlled appliance so an unintentional activation may occur if the wrong button
on the remote is pressed. Z-Wave devices can be automatically powered on by programmed events. Unattended or unintentional operation could result in hazardous conditions. Z-Wave enabled devices should never be used to supply power to, control
,
or monitor medical and/or life
support equipment.
NOTES
This Z-Wave device must be configured and added to a Z-Wave
network before it can be operated and controlled from a smart device.
Follow the instructions on the next page and the
manual(s) associated with the
Hub for configuration.
SMART METERING
The ZWN-323M
Plug-in
Smart Meter Module enables you to measure the energy usage of your
devices
. When added to a Z-Wave network, the Smart Meter Module reports real time data to your
Hub
or controller. It can also display actual consumption (in W
atts
) and the accumulated power
used (in kWh) in the user interface of the
Hub
. Please
follow the instructions on the manual(s)
associated with the Hub for configuration.
NEW
Z-WAVE 500 SERIES
FEATURES
−
50% improvement in battery life
−
67% improvement in range
−
250% more bandwidth
−
Three RF channels for improved noise immunity and higher bandwidth
−
New Plug-n-Play Network-wide Inclusion feature
−
Improved self-healing and fault tolerance with Explorer Frame feature
−
Standardized method for Over the Air firmware updates (OTA)
−
Improved product information capture for product certification database
−
Fully backward compatible
