manualshive.com logo in svg

VibrAlign Fixturlaser Go, Руководство по обучению


Поделиться
Скачать
background image

4.1  Rotate the sensors to 9:00. 

 

ƒ

9:00 is shown graphically on the screen, but 
it will not be animated as the sensors rotate. 
Remember, in the clock method the inclinometers 
are turned off.

 

ƒ

Standing behind the Movable Machine looking at 
the coupling, 9:00 is located on the left.

 

ƒ

You should see both “S” and “M” values in the 
boxes at the top of the display.

 

ƒ

If you do not, then the lasers are not within the 
sensors.

4.2 Press the “OK” button to register the 1st 

measurement.

 

ƒ

The “S” and “M” values will change to near zero.

 

ƒ

The values are displayed in mils.

 

ƒ

Do not rotate shafts while the Measuring icon is 
displayed. 

4.3  Rotate the sensors to approx. 3:00. 

 

ƒ

3:00 is shown graphically on the screen, but 
it will not be animated as the sensors rotate. 
Remember, in the clock method the inclinometers 
are turned off.

 

ƒ

Care should be taken to square the “S” and “M” 
sensors to one another if shafts are uncoupled.

 

ƒ

You should see both “S” and “M” values in the 
boxes at the top of the display.

 

ƒ

If you do not, then the lasers are not within the 
detectors.

4.4 Press the “OK” button to register the 2nd 

measurement.

 

ƒ

The “S” and “M” values will not change.

 

ƒ

Do not rotate shafts while the Measuring icon is 
displayed.

4.5  Rotate the sensors to 12:00. 

 

ƒ

12:00 is shown graphically on the screen, but 
it will not be animated as the sensors rotate. 
Remember, in the clock method the inclinometers 
are turned off.

 

ƒ

Care should be taken to square the “S” and “M” 
sensors to one another if shafts are uncoupled.

 

ƒ

You should see both “S” and “M” values in the 
boxes at the top of the display.

 

ƒ

If you do not, then the lasers are not within the 
sensors.

4.6 Press the “OK” button to register the 3rd 

measurement.

 

ƒ

The “S” and “M” values will not change.

 

ƒ

Do not rotate shafts while the Measuring icon is 
displayed.

5.  ALIGNMENT RESULTS

 

ƒ

Both the Vertical and Horizontal misalignment values 
are displayed. 

 

ƒ

Displayed values are not live.

 

ƒ

The angle and offset values ONLY determine the 
alignment condition. 

U S I N G   T H E   C L O C K   M E T H O D

34

Содержание Fixturlaser Go









































Отзывы:

Нет отзывов

Похожие инструкции для Fixturlaser Go

Бренды по названию

Популярные бренды

Загрузить еще бренды