background image

© Vestamatic GmbH

Ar

t.-Nr

.:

84501110 E1  •  

V

estamatic GmbH  •  Dohrw

eg 27  •  D-41066 Mönchengladbach  •  www

.v

estamatic.com

IF SMI KNX 24VDC

Subject to modifications.

5/ 15

G

In the case of common parametrisation for all channels (“all equal”), one
tab each for the administration and the mechanics of the channels is
shown. Settings on these tabs are active for all channels and drives at the
same time. With individual parametrisation, one tab with administration
parameters, one with mechanical parameters and the communication
objects available for this channel depending on the setting are shown
respectively for each channel selected as “used”.
Depending on the addressing mode set on the general tab, either a tab for
setting only the slave addresses appears (in the case of “automatic”
addressing) or two other tabs for registering the manufacturer and the key
IDs of the drives used (in the case of “per manufacturer and SMI key ID”
addressing).
For those lists of communication objects and parameters reproduced as
follows, reference is made in the “Dependent on” column as to which other
settings the appearance of the respective element is dependent on.
Special reference is, however, no longer made in detail to the basic depen-
dency that channel-specific objects only appear for activated channels.

Fig. ETS interface

ETS2, two channels activated,
individual parametrisation,
automatic addressing.

ETS interface

The configuration of the ETS interface (communication objects and para-
meters) is based on the blind actuators already available on the market.
This ensures that the device can be parametrised and activated by the
project manager with a minimal period of adjustment.

The parameters are systematically arranged on tabs. In addition to general
parameters, which are collectively active for the actuator, the selection of
channels or drives to be used and their SMI addressing can be defined on
two other tabs. All other tabs, parameters and communication objects are
shown or masked out depending on the channels selected and settings
carried out. Depending on the default setting, all of the up to eight chan-
nels are set as “unused” so that initially only two general communication
objects (lock and safety) and no other elements are illustrated for the
channels. Other communication objects and parameters only appear for
the channels selected as “used”.

Содержание IF SMI KNX 24VDC
















Отзывы: