background image

© Vestamatic GmbH

Ar

t.-Nr

.:

84501110 E1  •  

V

estamatic GmbH  •  Dohrw

eg 27  •  D-41066 Mönchengladbach  •  www

.v

estamatic.com

IF SMI KNX 24VDC

Subject to modifications.

6/ 15

G

Object no. Object name

Operating mode

Dependent on

Function

Type

Object flags

General objects (active for all channels at the same time)

0

Safety

On / Off

1 bit

AKS / receive

1

Travel command lock

On / Off

1 bit

AKS / receive

Channel-specific objects channel 1

2

Up/Down travel, channel 1

Manual mode

Up / Down

1 bit

AKS / receive

3

Stop/Step travel, channel 1

Manual mode

Up / Down

1 bit

AKS / receive

4

Sunshade, channel 1

Automatic mode

Automatic mode released

Up / Down

1 bit

AKS / receive

5

Automatic mode, channel 1

Automatic mode released

On / Off

1 bit

AKS / receive

6

Position of sunshade (%), channel 1

Automatic/manual

8-bit value

8 bit

AKS / receive

7

Position of slat angle (%), channel 1

Automatic/manual

Shade type blind

8-bit value

8 bit

AKS / receive

8

Position of sunshade status object (%), channel 1

8-bit value

8 bit

KLÜ / send

9

Position of slat angle status object (%), channel 1

Shade type blind

8-bit value

8 bit

KLÜ / send

10

Move to scene pos1/pos 2, channel 1

Manual mode

Pos 1 / Pos 2

1 bit

AKS / receive

11

Save scene pos1/pos 2, channel 1

Manual mode

Pos 1 / Pos 2

1 bit

AKS / receive

12

Drive error status, channel 1

On / Off

1 bit

KLÜ / send

Channel-specific objects channels 2 to 8

13

Up/Down travel, channel 2

Manual mode

Up / Down

1 bit

AKS / receive

14

Stop/Step travel, channel 2

Manual mode

Up / Down

1 bit

AKS / receive

15

Sunshade, channel 2

Automatic mode

Automatic mode released

Up / Down

1 bit

AKS / receive

16

Automatic mode, channel 2

Automatic mode released

On / Off

1 bit

AKS / receive

17

Position of sunshade (%), channel 2

Automatic/manual

8-bit value

8 bit

AKS / receive

18

Position of slat angle (%), channel 2

Automatic/manual

Shade type blind

8-bit value

8 bit

AKS / receive

...

...

...

...

...

...

...

85

Position of sunshade status object (%), channel 8

8-bit value

8 bit

KLÜ / send

86

Position of slat angle status object (%), channel 8

Shade type blind

8-bit value

8 bit

KLÜ / send

87

Move to scene pos1/pos 2, channel 8

Manual mode

Pos 1 / Pos 2

1 bit

AKS / receive

88

Save scene pos1/pos 2, channel 8

Manual mode

Pos 1 / Pos 2

1 bit

AKS / receive

89

Drive error status, channel 8

On / Off

1 bit

KLÜ / send

ETS communication objects

Fig. ETS communication objects
in ETS

One channel, blind, with automatic

Содержание IF SMI KNX 24VDC
















Отзывы: