VESPA 150 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 249

VESPA 150 Скачать руководство пользователя страница 94

IN ORDER TO AVOID DAMAGING THE ELECTRIC SYSTEM, NEVER DISCONNECT THE WIRING
WHILE THE ENGINE IS RUNNING. DO NOT TIP THE VEHICLE TOO MUCH IN ORDER TO AVOID
DANGEROUS LEAKAGE OF THE BATTERY ELECTROLYTE.

CAUTION

MODIFICATIONS OR REPAIRS TO THE ELECTRICAL SYSTEM, PERFORMED INCORRECTLY OR
WITHOUT STRICT ATTENTION TO THE TECHNICAL SPECIFICATIONS OF THE SYSTEM CAN
CAUSE MALFUNCTIONING AND RISK OF FIRE.

CAUTION

PROCEED WITH CAUTION.
DO NOT DAMAGE THE TONGUES OR THEIR SEATS. HANDLE THE PAINTED AND PLASTIC
COMPONENTS CAREFULLY. DO NOT SCRATCH OR DAMAGE THEM.

FUSE CHART

Specification

Desc./Quantity

Fuse No. 1

Capacity:

20 A

Protected circuits:

battery recharge circuit, fuses No. 2 and 3

(live), fuses No. 4 and 5.

Fuse No. 2

Capacity:

5 A

Protected circuits:

ignition switched live instrument panel, in-

dicators, antitheft device pre-installation, stop lights, starter

circuit, headlight relay, horn, daylight running lights.

Fuse No. 3

Capacity:

5 A

Protected circuits:

ignition switched live tilting sensor, control

unit.

Fuse No. 4

Capacity:

7.5 A

Protected circuits:

battery-powered control unit.

Fuse No. 5

Capacity:

10 A

Protected circuits:

battery-powered instrument panel, antith-

eft device pre-installation, headlight; ignition switched live sad-

dle opener actuator.

Electrical system

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

ELE SYS - 94

«
...
92
93
94
95
96
...
»

Содержание 150


























































































































































































































































Отзывы:

Нет отзывов