VESPA 150 Скачать руководство пользователя страница 115

Страница: 115 / 249

HEADLIGHT RELAY

Function

Controls the lights logic, the engine control unit

modifies at idle speed the intensity of the headlight

for maintaining battery.

Pin-out:

30. Battery positive

85. Live positive lead

86. Controlled by engine control unit

87. Headlight output

87A. Ground lead

ELECTRICAL ERRORS

Low headlamp voltage P1002

- shorted to negative.

Error cause

Short circuit to negative: null voltage at PIN 11 of the control unit connector.

Troubleshooting

Short circuit to negative:

- Remove the headlight relay from its base and ensure its correct functioning.

- Perform the check procedure of the control unit and relay base connector.

- Check the relay base connector PIN 86 from ground insulation.

- If there is no ground insulation restore the cabling.

High headlamp voltage P1001

- open circuit or short circuit to positive.

Error cause

Open circuit or short circuit to positive: interruption of the circuit or excessive voltage at PIN 11 of the

control unit connector.

Troubleshooting

Open circuit:

- Disconnect the connector of the control unit.

- Remove the headlight relay from its base and ensure its correct functioning.

- Perform the check procedure of the control unit and relay base connector.

- Check continuity of the cable harness between the control unit and relay base Control unit PIN 11 -

relay PIN 86. If necessary, restore the cable harness.

Short circuit to positive:

- With the headlight relay connector connected and the control unit disconnected, verify that the fault

is a short circuit with the battery positive of sensor connector PIN 86 (or control unit PIN 11) and restore

cable harness.

If the above tests provided a positive result, proceed with the following checks:

- Perform the check procedure of the control unit and relay base connector.

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Electrical system

ELE SYS - 115

Содержание 150


























































































































































































































































Результаты поиска

Содержание 150

Отзывы:

VESPA 150, Руководство по обслуживанию станции, Страница: 115 / 249

Результаты поиска

Содержание 150

Отзывы: