VESPA 150 Скачать руководство пользователя страница 24

Страница: 24 / 249

TANDARD

DIAMETER

Specification

Desc./Quantity

Camshaft check: Standard diameter

Bearing A Ø: 25.002 to 25.015 mm

Camshaft check: Standard diameter

Bearing B diameter: 12.002 to 12.013 mm

- Check the outside diameter of the rocker pins

- Check there are no signs of wear or scoring on the rocker pins.

- Check the internal diameter of each rocker arm.

- Check there are no signs of wear on the contact pads with the cam and on the jointed adjustment

plate.

IAMETER

PINS

AND

ROCKING

LEVERS

Specification

Desc./Quantity

Rocking lever inside diameter: Standard diameter (C)

Ø 10.015 to 10.035 mm

Rocking lever pin diameter: Standard diameter (D)

Ø 10.015 to 10.023 mm

Characteristics

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

CHAR - 24

Содержание 150


























































































































































































































































Результаты поиска

Содержание 150

Отзывы:

VESPA 150, Руководство по обслуживанию станции, Страница: 24 / 249

Результаты поиска

Содержание 150

Отзывы: