VESPA 150 Скачать руководство пользователя страница 227 | Manualshive

Страница: 227 / 249

VESPA 150 Скачать руководство пользователя страница 227

Brake fluid level check

- Rest the vehicle on its centre stand on flat

ground.

- The brake fluid reservoir has a sight glass «

A

»

made of transparent material; the quantity of liquid

contained in the sight glass indicates the level of

fluid in the reservoir.

- When the sight glass «

A

» is full, the level inside

the reservoir is above the MIN level; when it is par-

tially full, the level has dropped to the MIN level;

when it is fully empty, the level of fluid in the res-

ervoir is below the MIN level.

N.B.

THE LEVEL TENDS TO DROP AS THE BRAKE PADS GET
WORN, A MINIMUM LEVEL SHOULD NOT BE REACHED.
IF THE LEVEL IS TOO LOW, CHECK AND FIX THE SYSTEM
SEALS, IF REQUIRED. TOP UP THE PUMP RESERVOIR, IF
REQUIRED, CONSIDERING THAT THE "MAX." LEVEL
MUST ONLY BE OBTAINED WITH NEW PADS.

- Under standard climatic conditions, replace fluid as indicated in the scheduled maintenance table.

Front brake pump

Removal

- Remove the upper handlebar cover

- Remove the two screws fixing the brake pump to

the handlebar indicated in the photograph

- Remove the oil pipe joint from the pump

- Remove the connector from the stop lights switch

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Braking system

BRAK SYS - 227

«
...
225
226
227
228
229
...
»

Содержание 150


























































































































































































































































Отзывы:

Нет отзывов