VESPA 150 Скачать руководство пользователя страница 206

Страница: 206 / 249

- Heat the roller bearing seat with a heat gun

- Use the specific tool to introduce and push the

bearing until it stops, with the shielded side facing

out

- Refit the ball bearing check Seeger ring

Specific tooling

020151Y

Air heater

020376Y

Adapter handle

020357Y

32 x 35 mm adaptor

020412Y

15 mm guide

- Use the specific tool to fit and push the roller cas-

ing until it stops

- Refit the oil seal on the roller bearing side

- Lubricate the area between the roller bearing and

the ball bearing

Specific tooling

020038Y

Punch

Recommended products

AGIP GREASE MU3

Yellow-brown, lithium-

base, medium-fibre multipurpose grease.

ISO L-X-BCHA 3 - DIN 51 825 K3K -20

- To refit, follow the removal steps but in reverse order; be careful to tighten to the prescribed torque.

Locking torques (N*m)

Front wheel axle nut

75 to 90

Refitting the front wheel

- Upon refitting, tighten the five screws to the pre-

scribed torque.

Locking torques (N*m)

Wheel rim screws

20 - 25

Handlebar

Suspensions

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

SUSP - 206

Содержание 150


























































































































































































































































Результаты поиска

Содержание 150

Отзывы:

VESPA 150, Руководство по обслуживанию станции, Страница: 206 / 249

Результаты поиска

Содержание 150

Отзывы: