VESPA 150 Скачать руководство пользователя страница 49

Страница: 49 / 249

Safety valve check

The cleaning of the canister is achieved via a controlled flow of air from the vacuum socket in the intake

manifold.

To ensure that the engine works properly, it is necessary that the flow of air is not too intense, this is

achieved by means of a restricted section 0.0354in (0.9 mm) formed in the socket on the intake manifold.

The relative connecting pipe with the canister, includes the installation of the safety valve.

This is a one-way valve which ensures the passage of air in the direction of the manifold when the

control vacuum is greater than 2.9PSI (20kPa) (200mbar).

The vacuum of the engine at idle, causes a slight flow of air easily compensated by the idle speed

adjustment parameters.

When the vehicle is stopped, the safety valve will be closed due to the lack of control vacuum therefore,

any expansion of the fuel tank, will not cause pollution of the intake manifold, and then cause flooding

of the engine.

To control the valve, it is preferable to it, alterna-

tively just access the manifold side pipe.

•

Connect the MITY-VAC pump on the

engine side duct.

•

Select the pump command on the "vac-

uum" position, then slowly apply vac-

uum up to the valve threshold check

opening.

If you detect different pressures, replace the valve.

N.B.

An opening vacuum that is too high, causes

a lack of regeneration of the activated carbon; vice

versa, an opening vacuum that is too low, increa-

ses the flow of air to the engine causing the thin-

ning of idle.

Characteristic

Standard opening vacuum

(2.90-3.77)PSI (20-26)kPa (200-260)mbar

Roll-over valve check

The valve must enable the following results:

•

Aeration of the tank while riding (the ambient air enters the tank in relation to the volume of

fuel used).

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Maintenance

MAIN - 49

Содержание 150


























































































































































































































































Результаты поиска

Содержание 150

Отзывы:

VESPA 150, Руководство по обслуживанию станции, Страница: 49 / 249

Результаты поиска

Содержание 150

Отзывы: