manualshive.com logo in svg

VESPA 150, Руководство по обслуживанию станции, Страница: 23 / 249

Поделиться
Скачать
VESPA 150 Скачать руководство пользователя страница 23

- After measuring the valve guide diameter and the

valve stem diameter, check the clearance be-

tween guide and stem.

INTAKE

Specification

Desc./Quantity

Standard clearance:

0.10 mm

Limit allowed:

0.08 mm

EXHAUST

Specification

Desc./Quantity

Standard clearance:

0.15 mm

Limit allowed:

0.1 mm

- Check that there are no signs of wear on the faying surface with the set screw articulated terminal.

- If no faults are found during the above checks, the same valves can be reused. For better sealing

results, we recommend grinding the valve seats. Grind the valves gently with fine-grained lapping com-

pound. Upon grinding, keep the cylinder head in horizontal position. This will prevent the lapping

compound residues from penetrating between the valve stem and the guide (see figure).

CAUTION

TO AVOID SCORING THE FAYING SURFACE, DO NOT ROTATE THE VALVE WHEN NO LAPPING
COMPOUND IS LEFT. CAREFULLY WASH THE CYLINDER HEAD AND THE VALVES WITH A
SUITABLE PRODUCT FOR THE TYPE OF LAPPING COMPOUND BEING USED.

CAUTION

DO NOT CHANGE THE VALVE FITTING POSITION (RH - LH).

- Check the camshaft bearings for signs of abnormal wear or scores.

- Using a micrometer, measure the camshaft bearings.

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Characteristics

CHAR - 23

Содержание 150


























































































































































































































































Отзывы:

Нет отзывов