VESPA 150 Скачать руководство пользователя страница 142

Страница: 142 / 249

020151Y

Air heater

020376Y

Adapter handle

020360Y

52 x 55-mm adaptor

020364Y

25-mm Guide

Fitting the transmission gear bearing

- Use the heat gun to heat the bearing seat.

- Using the equipment set a new bearing.

Specific tooling

020151Y

Air heater

020376Y

Adapter handle

020359Y

42 x 47-mm adaptor

020412Y

15 mm guide

Refitting the hub bearings

- Insert the gears in the cover in order to prevent

abnormal movements during insertion into the en-

gine.

- Insert the wheel axis.

Refitting the ub cover

- Clean the engine crankcase and reduction cover

surfaces adequately.

- Working in reverse with respect to the disassem-

bly, inert the command pinion and the intermediate

gear into the hub box.

- Pay attention to the correct positioning of the

alignment dowels.

- Insert the gasket.

Engine

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

ENG - 142

Содержание 150


























































































































































































































































Результаты поиска

Содержание 150

Отзывы:

VESPA 150, Руководство по обслуживанию станции, Страница: 142 / 249

Результаты поиска

Содержание 150

Отзывы: