VersaLogic Lion VL-EPMe-42 Скачать руководство пользователя страница 31

Страница: 31 / 38

FPGA Registers

Lion (VL-EPMe-42) Programmer’s Reference Manual

TEMPICR – Temperature Interrupt Control Register

This is the interrupt mask register for the temperature sensor thermal alerts and the DDR3 SODIMM
EVENT signals and the interrupt enable and selection. The SODIMM may not have any temperature event
capability.

Reset type is Platform.

Table 31: TEMPICR – Temperature Interrupt Control Register

Bits

Identifier

Access

Default

Description

IRQEN

R/W

Temperature interrupt enable/disable:
0 – Interrupts disabled
1 – Interrupts enabled

6-4

IRQSEL(2:0)

R/W

000

Temperature interrupt IRQ select in LPC SERIRQ:

000 – IRQ3
001 – IRQ4
010 – IRQ5
011 – IRQ10
100 – IRQ6
101 – IRQ7
110 – IRQ9
111 – IRQ11

IMASK_BATTLOW

R/W

Battery-low interrupt mask:
0 – Interrupt disabled
1 – Interrupt enabled.

IMASK_EVENT

R/W

SODIMM EVENT output interrupt mask:
0 – Interrupt disabled
1 – Interrupt enabled.

IMASK_THERM

R/W

Temperature Sensor THERM output interrupt mask:
0 – Interrupt disabled
1 – Interrupt enabled.

IMASK_ALERT

R/W

Temperature Sensor ALERT output interrupt mask:
0 – Interrupt disabled
1 – Interrupt enabled.

Содержание Lion VL-EPMe-42







































Результаты поиска

Содержание Lion VL-EPMe-42

Отзывы:

Бренды по названию

Популярные бренды

VersaLogic Lion VL-EPMe-42, Справочное руководство

Результаты поиска

Содержание Lion VL-EPMe-42

Отзывы:

Бренды по названию

Популярные бренды