VersaLogic Lion VL-EPMe-42 Скачать руководство пользователя страница 27

Страница: 27 / 38

FPGA Registers

Lion (VL-EPMe-42) Programmer’s Reference Manual

WDT_CTL – Watchdog Control Register

Reset type is Platform.

Table 24: WDT_CTL – Watchdog Control Register

Bits

Identifier

Access

Default

Description

IRQEN

R/W

Watchdog interrupt enable/disable:

0 – Interrupts disabled

1 – Interrupts enabled

6-4

IRQSEL(2:0)

R/W

000

Watchdog interrupt IRQ select in LPC SERIRQ:

000 – IRQ3

001 – IRQ4

010 – IRQ5

011 – IRQ10

100 – IRQ6

101 – IRQ7

110 – IRQ9

111 – IRQ11

Reserved

Reserved. Writes are ignored; reads always return 0.

RESET_EN

R/W

Enable the Watchdog to assert the push-button reset if it “fires”.

0 – Watchdog will not reset the board

1 – Board will be reset if the Watchdog “fires”

WDT_EN

R/W

Watchdog Enable:

0 – Watchdog is disabled

1 – Watchdog is enabled

Note:

The WDT_VAL register must be set before enabling.

WDT_STAT

Watchdog Status:

0 – Watchdog disabled or watchdog has not “fired”

1 – Watchdog fired.

Note:

Once set to a ‘1’, it will remain so until any of the following

occurs:

•

the WDT_VAL register is written to

•

the WDT_EN is disabled

•

a reset occurs

Содержание Lion VL-EPMe-42







































Результаты поиска

Содержание Lion VL-EPMe-42

Отзывы:

Бренды по названию

Популярные бренды

VersaLogic Lion VL-EPMe-42, Справочное руководство

Результаты поиска

Содержание Lion VL-EPMe-42

Отзывы:

Бренды по названию

Популярные бренды