manualshive.com logo in svg

VersaLogic Lion VL-EPMe-42, Справочное руководство

Поделиться
Скачать
VersaLogic Lion VL-EPMe-42 Скачать руководство пользователя страница 13

FPGA Registers 

Lion (VL-EPMe-42) Programmer’s Reference Manual 

9 

BIOS and Jumper Status Register 

Table 6: SCR –Status/Control Register 

Bit 

Identifier 

Access 

Default 

Description 

7 

BIOS_JMP 

RO 

N/A 

Status of the external BIOS switch (jumper): 

1 – Primary BIOS selected 

0 – Secondary BIOS selected 

6 

BIOS_OR 

R/W 

0 

BIOS Switch (jumper) Override 

0 – BIOS Select will follow the BIOS_JMP switch setting. (

Note

) 

1 – BIOS Select will follow the BIOS_SEL register setting 

Note:

 See Table 7 

5 

BIOS_SEL 

R/W 

0 

BIOS Select (see BIOS_OR): 

1 – Primary BIOS selected 

0 – Backup BIOS selected 

Note: 

See Table 7 

4 

LED_DEBUG 

R/W 

0 

Debug LED (controls the yellow LED): 

0 – LED is off and follows its primary function (MSATA_DAS) 

1 – LED is on (indicates FPGA is programmed by default) 

3 

WORKVER 

RO 

N/A 

Status used to indicate that the FPGA is not officially released 
and is still in a working state.  

0 – FPGA is released 

1 – FPGA is in a working state (not released) 

2 

RESERVED 

RO 

N/A 

Reserved. Writes are ignored; reads always return 0. 

1 

GPI_JMP 

RO 

N/A 

Status of the GPI Jumper (switch): 

0 – Switch is Off 

1 – Switch is On 

0 

RESERVED 

RO 

0 

Reserved. Writes are ignored; reads always return 0. 

Note:

  

This corresponds to the setting of position 6 of the SW1 Configuration Switch block. Refer to the 

EPMe-42 Hardware Reference Manual

 for more information regarding the configuration switches.

 

 
The table below summarizes the modes related to BIOS_OR and BIOS_SEL and the BIOS Configuration 
Switch 6. The external BIOS selection is determined by the combination of the FPGA BIOS selection 
signals and the BIOS Configuration Switch.  This allows the BIOS Configuration switch to still be used to 
select the Secondary BIOS no matter what the internal FPGA settings are or when the FPGA is not 
programmed (i.e., setting the BIOS Configuration to the “ON” position will always select the Secondary). 

Содержание Lion VL-EPMe-42







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды