VersaLogic Lion VL-EPMe-42 Скачать руководство пользователя страница 12

Страница: 12 / 38

FPGA Registers

Lion (VL-EPMe-42) Programmer’s Reference Manual

FPGA Register Descriptions

Register Access Key

R/W

Read/Write

Read-only (status or reserved)

R/WC

Read-status/Write-1-to-Clear

RSVD

Reserved. Only write 0 to this bit; ignore all read values.

Product Information Registers

This register drives the PLED on the paddleboard. It also provides read access to the product code.

Table 4: PCR – Product Code and LED Register

Bit

Identifier

Access

Default

Description

PLED

R/W

Drives the programmable LED on the paddleboard.

0 – LED is off (default)

1 – LED is on (can be used by software)

6-0

PRODUCT_CODE

0010101

Product Code for the EPMe-42 (0x15)

Table 5: PSR – Product Status Register

Bit

Identifier

Access

Default

Description

7:3

REV_LEVEL[4:0]

N/A

Revision level of the PLD (incremented every FPGA release)

EXTEMP

N/A

Extended or Standard Temp Status (set via external resistor):

0 – Standard Temp

1 – Extended Temp (probably always set)

CUSTOM

N/A

Custom or Standard Product Status

0 – Standard Product

1 – Custom Product or PLD/FPGA

BETA

N/A

Beta or Production Status

1 – Beta (or Debug)

0 – Production

Содержание Lion VL-EPMe-42







































Результаты поиска

Содержание Lion VL-EPMe-42

Отзывы:

Бренды по названию

Популярные бренды

VersaLogic Lion VL-EPMe-42, Справочное руководство

Результаты поиска

Содержание Lion VL-EPMe-42

Отзывы:

Бренды по названию

Популярные бренды