Vermont Castings RFSDV34 Скачать руководство пользователя

Страница: 32 / 36

RFSDV34 Freestanding Direct Vent Gas Stove

10003550

Optional Brass Trim Kit

decorative brass window trim kit, Model RFSDV34TKAP/

S is available for the RFSDV34 Freestanding Stove.

Kit contents:

(1) Brass window trim

(8) Magnets

(3) Brass trim rings (for the vent pipe joints)

Installation Procedure

1. Unpack the kit and confirm all parts are present.
. It is very important to remove all the protective plastic

wrap from the brass components

3. Attach the magnets to the trim. (Fig. 50)
4. Position trim against the stove window frame assem-

bly. The trim will be held in place by the magnets.

5. Fit the brass rings in place around any visible vent

joints.

NOTE: Use only lemon oil to clean this window trim

as directed below. Lemon oil can be obtained from

supermarkets and hardware stores. Do not use brass

polish or household cleaners, as these products will

damage the trim.

Remote Control Options

These remote controls are available as an option only on

stoves fitted with RN/RP gas control valves.

Thermostatic Remote

RCST, RCT, RCSTE,

Control

RCSTEB, RCSIT,

RCSITE, WWTD

Remote Control On/Off

RCB, RCMT, RCBE,

WMTD

Wall Thermostat Kit

Wall Switch Kit

MVWS

FP1522

window trim

6/04

FP15

Place Magnets Here

Fig. 50

RFSDV34TKA magnet locations.

Clean brass trim with a soft clean cloth slightly damp-

ened with lemon oil. Buff with a soft dry cloth.

Содержание RFSDV34





































Результаты поиска

Содержание RFSDV34

Отзывы:

Похожие инструкции для RFSDV34

Бренды по названию

Популярные бренды

Vermont Castings RFSDV34, Инструкции по установке и руководство для владельца

Результаты поиска

Содержание RFSDV34

Отзывы:

Похожие инструкции для RFSDV34

Бренды по названию

Популярные бренды