Vermont Castings RFSDV34 Скачать руководство пользователя

Страница: 20 / 36

RFSDV34 Freestanding Direct Vent Gas Stove

10003550

3. Open control access panel.

4. Push in gas control knob slightly and turn clockwise

to “OFF”. Do not force.

5. Close control access panel.

STOP!

Read the safety information above.

. Turn off all electrical power to the unit.

3. Turn the ON/OFF switch to “OFF” position or set

thermostat to lowest level.

4. Open control access panel.

5. Push in gas control knob slightly and turn clockwise

to “OFF”.

10. Push the control knob all the way in and hold. Im-

mediately light the pilot by repeatedly depressing the

piezo spark ignitor until a flame appears. Continue

to hold the control knob in for about one (1) minute

after the pilot is lit. Release knob and it will pop back

up. Pilot should remain lit. If it goes out, repeat steps

5 through 8.

FOR YOUR SAFETY READ BEFORE LIGHTING

Follow the gas supplier’s instructions.

•

If you cannot reach your gas supplier, call the

Fire Department

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in or

turn by hand, do not try to repair it, call a qualified

service technician. Applying force or any attempted

repair may result in a fire or explosion.

D. Do not use this stove if any part has been under wa-

ter. Immediately call a qualified service technician

to inspect the heater and to replace any part of the

control system and any gas control which has been

under water.

A. This heater has a pilot which must be lit manually.

When lighting the pilot follow these instructions

exactly.

B. BEFORE LIGHTING smell all around the heater

area for gas. Be sure to smell next to the floor be-

cause some gas is heavier than air and will settle

on the floor.

WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance

•

Do not touch any electric switch

•

Do not use any phone in your building

•

Immediately call your gas supplier from a

neighbor’s phone.

To Turn Off Gas To Heater

Lighting and Operating Instructions

1. Turn the ON/OFF switch to Off position or set the

thermostat to lowest setting.

. Turn off all electric power to the unit if service is

to be performed.

Lighting Instructions

6. Wait five (5) minutes to clear out any gas. Then

smell for gas, including near the floor. If you smell

gas, STOP! Follow “B” in the safety information

above. If you do not smell gas, go to the next

step.

7. Remove glass door before lighting pilot. (See

Glass Frame Removal section).

8. Visibly locate pilot by the main burner.

9. Turn knob on gas control counterclockwise

to “PILOT”.

• If knob does not pop up when released, stop

and immediately call your service technician or gas

supplier.

• If after several tries, the pilot will not stay lit, turn

the gas control knob to “OFF” and call your service

technician or gas supplier.

11. Replace glass door.

1. Turn gas control knob to “ON” position.

13. Turn the ON/OFF/RS switch to “ON” position or set

thermostat to desired setting.

14. Turn on all electrical power to the unit.

WARNING: If you do not follow these instructions exactly, a fire or explosion

may result causing property damage, personal injury or loss of life.

SIT NOVA

PILOT

OFF

PILOT

OFF

OFF

PILOT

FP1067

lighting instruction

knobs

3/9/01 djt

3/8" - 1/2"

FP1068
Lighting instructions
Pilots

Содержание RFSDV34





































Результаты поиска

Содержание RFSDV34

Отзывы:

Похожие инструкции для RFSDV34

Бренды по названию

Популярные бренды

Vermont Castings RFSDV34, Инструкции по установке и руководство для владельца

Результаты поиска

Содержание RFSDV34

Отзывы:

Похожие инструкции для RFSDV34

Бренды по названию

Популярные бренды