Vermont Castings RFSDV34 Скачать руководство пользователя

Страница: 26 / 36

RFSDV34 Freestanding Direct Vent Gas Stove

10003550

Symptom

1. Battery icon on LCD on transmit-

ter.

. LCD display is blank.

3. LCD display shows “funny” dis-

play.

4. Appliance does not come on.

5. Receiver cannot receive signal.

6. Blower is not on after the stove is

turned on.

Causes

1. Low battery.

1. Wiring/Electrical connections.

. Privacy (DIP) switch setting on

transmitter does not match re-

ceiver.

3. Transmitter measure tem-

perature exceeding 99°F and

shows “HI” on LCD.

4. Distance between the trans-

mitter and receiver is more

than 30 feet.

1. Receiver is installed in an en-

closure.

1. Blower setting is off.

. Blower delay setting is set too

high.

Action

1. Replace batteries. Change the bat-

teries every 6 months.

. Check battery installation or replace

batteries.

3. Press reset button at the back of the

transmitter.

1. Slide the switch to ON, if appliance

comes on, wiring is not the cause.

. If appliance, does not come on,

check wiring connections.

1. Make sure the transmitter and re-

ceiver have the same DIP switch

settings.

1. Move transmitter to a cooler place

and wait until temperature drops be-

low 99°.

1. Make sure the operating distance is

less than 30 feet.

1. Make sure the receiver is not locat-

ed inside too tight of an enclosure.

1. Press FAN key to select desired fan

speed.

. Press and hold Fan key to set de-

sired ON/OFF delays. This is done

in minutes.

Troubleshooting

Содержание RFSDV34





































Результаты поиска

Содержание RFSDV34

Отзывы:

Похожие инструкции для RFSDV34

Бренды по названию

Популярные бренды

Vermont Castings RFSDV34, Инструкции по установке и руководство для владельца

Результаты поиска

Содержание RFSDV34

Отзывы:

Похожие инструкции для RFSDV34

Бренды по названию

Популярные бренды