background image

20306750  3/15  Rev. 3

 

Designer Series Direct Vent Gas Fireplace
Installation and Operating Instructions

Models: STLDVP(N/P)SC, PFLDV(N/P)PSC, CRLDVP(N/P)SC, CLLDVP(N/P)SC

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for 

future reference.

• 

Do not store or use gasoline or other 
fl ammable vapors and liquids in the 
vicinity of this or any other appliance.

• 

WHAT TO DO IF YOU SMELL GAS

 

– Do not try to light any appliance.

 

– Do not touch any electrical switch; do 

not use any phone in your building.

 

– Leave the building immediately.

 

– Immediately call your gas supplier from 

a neighbor's phone. Follow the gas 
supplier's instructions.

 

– If you cannot reach your gas supplier, 

call the fi re department.

• 

Installation and service must be performed 
by a qualifi ed installer, service agency or 
the gas supplier.

WARNING: Improper installation, adjustment, 
alteration, service or maintenance can cause 
injury or property damage. Refer to this manual. 
For assistance or additional information consult 
a qualified installer, service agency or the 
gas supplier.   

This appliance may be installed in an aftermarket,* 
permanently located, manufactured home (USA 
only) or mobile home, where not prohibited by 
local codes.

This appliance is for use only with the type of gas 
indicated on the rating plate. This appliance is 
not convertible for use with other gases, unless 
a certifi ed kit is used. 

*  Aftermarket: Completion of sale, not for purpose of resale, from 

the manufacturer. 

 WARNING: 
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly 
could result in serious injury, death or 
property damage.

DANGER

HOT GLASS 

WILL

CAUSE BURNS

.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from 

the hot viewing glass is provided with this 

appliance and shall be installed.

CERTIFIED

S

AFETY

 

B

ARRIER

Содержание CLLDVPNSC

































































Отзывы: