CFDV Series Gas Fireplace
4
20306739
IMPORTANT SAFETY INFORMATION
13. You must keep control compartments, burners, and
circulating air passages clean. More frequent cleaning
may be needed due to excessive lint and dust. Turn off
the gas valve and pilot light before cleaning fi replace.
14. Have venting system inspected annually by a quali-
fi ed service person. If needed, have venting system
cleaned or repaired. Refer to
Cleaning and Mainte-
nance
, Page 47.
15. Keep the area around your fi replace clear of combus-
tible materials, gasoline, and other fl ammable vapor
and liquids. Do not run fi replace where these are used
or stored. Do not place items such as clothing or deco-
rations on or around fi replace.
16. Do not use this fi replace to cook food or burn paper or
other objects.
17. Never place anything on top of fi replace.
18. Do not use any solid fuels (wood, coal, paper, card-
board, etc.) in this fi replace. Use only the gas type
indicated on rating plate.
19. This appliance, when installed, must be electrically
grounded in accordance with local codes or in the
absence of local codes, with the
National Electrical
Code, ANSI/NFPA 70
, or the
Canadian Electrical Code,
CSA C22.1.
20. Do not obstruct the fl ow of combustion and ventilation
air in any way. Provide adequate clearances around
air openings into the combustion chamber along with
adequate accessibility clearance for servicing and
proper operation.
21. Do not use fi replace if any part has been under water.
Immediately call a qualified service technician to
inspect the appliance and to replace any part of the
control system and any gas control which as been
under water.
22. Do not operate fi replace if any log is broken.
23. Do not use a blower insert, heat exchanger insert, or
any other accessory not approved for use with this
fi replace.
24. Do not operate appliance with the glass front
removed, cracked, or broken. Replacement of the
glass should be done by a licensed qualifi ed ser-
vice person.
W
ARNING
Never connect unit to private (non-utility)
gas wells. This gas is commonly known
as wellhead gas.
IMPORTANT:
PLEASE READ THE FOLLOWING
CAREFULLY
It is normal for fi replaces fabricated of steel
to give off some expansion and/or contraction
noises during the start up or cool down cycle.
Similar noises are found with your furnace heat
exchanger or car engine.
IMPORTANT:
PLEASE READ THE FOLLOWING
CAREFULLY
It is not unusual for gas fi replace to give off some
odor the fi rst time it is burned. This is due to the
manufacturing process.
Please ensure that your room is well ventilated
during burn off — open all windows.
It is recommended that you burn your fi replace
for at least ten (10) hours the fi rst time you use it.
Place the fan switch in the “OFF” position during
this time.
CODE APPROVAL
Direct Vent type appliances draw all combustion air from
outside of the dwelling through the vent pipe.
These appliances have been tested by CSA and found to
comply with the established standards for DIRECT VENT
GAS FIREPLACE HEATERS in the USA and Canada as
follows:
LISTED VENTED GAS FIREPLACE HEATER
TESTED TO:
ANSI Z21.88-2014/CSA 2.33-2014 STANDARDS
The installation must conform with local codes or, in the
absence of local codes, with the
National Fuel Gas Code,
ANSI Z223.1/NFPA 54
, or the
National Gas and Propane
Installation Code, CSA B149.1
.
A manufactured home (USA only) or mobile home OEM
installation must conform with the
Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280,
or when such a standard is not applicable, the
Standard for
Manufactured Home Installations, ANSI/NCSBCS A225.1
,
or
Standard for Gas Equipped Recreational Vehicles and
Mobile Housing, CSA Z240.4
.
