manualshive.com logo in svg
background image

Z207135-0C 

Page 6 of 10 

©2016 Veris Industries   USA 800.354.8556 or +1.503.598.4564  / [email protected] 0916 

 

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of  Veris Industries, L.L.C. in the USA and/or other countries.

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

TM

Installation Guide

Air Quality

Example:  No Parity, 19200 Baud, Autobaud Off

1

2

3

4

5

off

off

on

off

off

None

19200 Baud

Autobaud Off

Function Codes

Function Code

Function

03

Read holding registers

06

Write single register

08

Diagnostics (Sub-function 00 – Return query data)

16

Write multiple registers

17

Report slave ID – Returns manufacturer, model name, and serial number (standard Veris format)

All of these values correspond to BACnet objects with the same name. See the BACnet Conformance Statement for 
their definitions. 

Note that an attempt to write to “read only” holding registers will give an error and the entire write command will 
not be executed even if writing to read/write locations were also requested. Exception code 2 is given in this case. 
“Preserved” means the values is maintained through power outages.

Holding Registers

Register

Description

1

Sensor measurement (read only)

2

Sensor scale factor (n in 10

n

, value would be -2 for percent, -6 for ppm) (read only)

3,4

Sensor measurement in IEEE 32-bit floating point.  Most significant word first. (read only)

5

Alarm bit map (read only)  

Bit 0 (lsb) – High set-point exceeded 

Bit 1 – Low set-point exceeded 

Bits 2-15 – Zero

6

Alarm bit map override 

Bit 0 – High set-point override  

Bit 1 – Low set-point override  

Bit 2 – High set-point level (1 – Above, 0 – Below)  

Bit 3 – Low set-point level  

Bits 4-15 – Zero

7

Time to sensor replacement (days remaining) (read only)

8

Run time (days) (read only)

9

Status (read only)  

Bit 0 – Over range  

Bit 1 – Warmup  

Bit 2 – Damage detected  

Bits 3-15 – Zero

10-17

Sensor gas type (read only). For example, CO. 

All strings packed two characters, big endian,  per word. Short strings null terminated.

18-25

Sensor serial number (read only) (always eight hexadecimal digits)

26-41

Manufacturer (read only) “Veris Industries”

42-57

Model (read only) “GWNPxx”

Configuration (cont.)

Modbus Point Map

Содержание GWNP Series











Отзывы: