background image

MA-SE-DCT3-01-02 Manual Doge CT3 eng rev2 

 

   Rev.4 Pagina 13 di 17 

 

GUIDE TO VELA REMOTE CONTROL SETTING 

 
 

 

 
 
 
 
 
 

NO 

NO 

YES 

YES 

TESTING

 

Push A button of the remote 

control 

Does LED 2 make a GREEN flash? 

Push B button of the remote control 

Does LED 2 of the remote 

control make a RED flash? 

END 

Set the receiver once 

again: 

SEE VELA REMOTE 

CONTROL MANUAL 

NO 

YES 

NO 

YES 

YES 

YES 

YES 

NO 

Connect the remote control receiver 

to DOGE CT3 using the dedicated 

cable 

(Picture 7) 

Give power supply to DOGE CT3, 

using a battery or a power supply 

unit 

Do the 2 LEDs of the receiver make 

a GREEN flash? 

Push the button of the receiver three 

times 

Is LED 2 of GREEN colour? 

Push A button of the remote control 

Does LED 2 make a flash? 

Push the remote control 

button four times 

 

Is LED 2 of RED colour? 

Push B button of the remote control 

Push once the button of the receiver 

Are the receiver 

LEDs turned off? 

Check 

the 

connecti

ons 

Push the 

remote 

control 

button 

once 

more 

PASS TO TESTING 

Push the 

remote 

control 

button 

once 

more 

NO 

Содержание DOGE CT3


















Отзывы: