background image

Models VCFI-3 and VCFI-6 are the ideal choice for providing year-round comfort in air circulation and destratification 
applications. Featuring an aerodynamic, extruded aluminum airfoil design and a high efficiency direct drive motor, 
model VCFI delivers maximum airflow at a fraction of the operating cost of other HVLS fans. And, with its universal 
ceiling mount, the VCFI fan is the easiest HVLS fan to install in the market!

IMPORTANT: 

To reduce the risk of fire, electric shock, 

or injury to persons, Model VCFI fans must be installed 
with a mount assembly, motor assembly and airfoils that 
are marked (on their cartons) to indicate suitability with 
this model. Other mounts, motors, and airfoils cannot 
be substituted.

WARNING

To reduce the risk of fire, electric shock, or injury to 
persons, observe the following:
  1.  Use this unit only in the manner intended by the 

manufacturer. If you have questions, contact the 
manufacturer.

  2.  Before servicing or cleaning unit, switch 

power off at service panel and lock the service 
disconnecting means to prevent power from 
being switched on accidentally. When the service 
disconnecting means cannot be locked, securely 
fasten a prominent warning device, such as a tag, 
to the service panel.

WARNING

To reduce the risk of fire, electric shock, or injury to 
persons, observe the following:
  1.  Installation work and electrical wiring must be 

done by qualified person(s) in accordance with all 
applicable codes and standards, including fire-
rated construction.

  2.  When cutting or drilling into wall or ceiling, do 

not damage electrical wiring and other hidden 
utilities.

WARNING

This appliance can be used by children aged from 8 
years and above and persons with reduced physical, 
sensory or mental capabilities or lack of experience 
and knowledge if they have been given supervision or 
instruction concerning use of the appliance in a safe 
way and understand the hazards involved. Children 
shall not play with the appliance. Cleaning and user 
maintenance shall not be made by children without 
supervision.

General Safety Information

IMPORTANT: 

VCFI fans must be installed with the supplied CAT-5e communication cable or shielded CAT-5e 

(by others) that complies with the following specifications. Cable must be twisted pair, shielded 26 ga. CAT-5e 
cable with a drain wire and must be compliant with ISO 11801. Cable must use shielded RJ45 connectors with 
a soldered drain and wiring configuration must follow EIA/TIA T568B wiring pinout. Individual CAT-5e cable 
lengths must not exceed 200 ft. in order to prevent network communication issues.

High Volume, Low Speed Ceiling Fans

1

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble, install, 
operate or maintain the product described. Protect yourself and others by observing all safety information. Failure 
to comply with these instructions will result in voiding of the product warranty and may result in personal injury 
and/or property damage.

Document 483907 

Model VCFI

High Volume, Low Speed Ceiling Fans

Содержание VCFI Series

























Отзывы: