![background image](http://html1.mh-extra.com/html/veab-heat-tech/cv-series/cv-series_fitting-instructions-manual_3706951169.webp)
17
CV
F
F
F
F
F
F
A = Intern börvärdespotentiometer. Används endast i värmare typ -1PTU/-1PTUL.
B = Bygel (Int/Ext) skall vara SLUTEN.
C = Trimpotentiometer justerad vid tillverkningen av regulatorn. Ändra INTE inställningen!
D = Börvärdesinställning för MIN-begränsning.
E = Börvärdesinställning för MAX-begränsning.
F = Bygel (MAX) skall vara SLUTEN om MAX-begränsningsfunktionen skall vara aktiverad. ÖPPEN bygel inaktiverar funktionen.
G = Bygel (MIN) skall vara SLUTEN om MIN-begränsningsfunktionen skall vara aktiverad. ÖPPEN bygel inaktiverar funktionen.
En röd lysdiod (LED) indikerar att effekten styrs ut.
OBS !
Kretskortet är spänningsförande när värmarens matningsspänning är ansluten.
A = Internes Sollwertpotentiometer. Nur mit Heizregisters vom Typ -1PTU/-1PTUL verwendet.
B = Der Bügel (Int/Ext) muss GESCHLOSSEN sein.
C = Das Einstellpotentiometer wurde bei der Herstellung des Reglers eingestellt. Einstellung NICHT ändern!
D = Sollwertpotentiometer für die MIN-Begrenzungsfunktion.
E = Sollwertpotentiometer für die MAX-Begrenzungsfunktion.
F = Der Bügel (MAX) muss GESCHLOSSEN sein, wenn die MAX-Begrenzungsfunktion aktiv ist. Und OFFEN, wenn NICHT aktiv ist.
G = Der Bügel (MIN) muss GESCHLOSSEN sein, wenn die MIN-Begrenzungsfunktion aktiv ist. Und OFFEN, wenn NICHT aktiv ist.
Eine rote Leuchtdiode (LED) zeigen an, dass die Leistung nach aussen abgegeben wird.
HINWEIS !
Die Leiterplatte steht unter Spannung, sobald das Heizgerät eingeschaltet ist.
WAARSCHUWING !
De printplaat staat onder spanning, zodra de voedingsspanning aangesloten is.
A =
.
B = Jumper (Int/Ext) moet KORTGESLOTEN zijn.
C = Trimpotentiometer is af fabriek ingesteld. NIET verstellen!
D = Setpoint voor MIN-begrenzing.
E = Setpoint voor MAX-begrenzing.
F = Jumper (MAX) moet KORTGESLOTEN zijn, om de functie voor MAX-begrenzing te activeren. OPEN jumper deactiveert deze functie.
G = Jumper (MIN) moet KORTGESLOTEN zijn, om de functie voor MIN-begrenzing te activeren. OPEN jumper deactiveert deze functie.
Instelpotentiometer voor de richtwaarde. Wordt alleen toegepast in verwarmingen van het type -1PTU/-1PTUL
Een rood licht emitterende diode (LED) geeft aan dat het vermogen wordt geregeld.
A = Internal set value potentiometer. Used in heaters type -1PTU/-1PTUL only.
B = Jumper (Int/Ext) must be SHORTED.
C = Trim potentiometer set at manufactoring. Do NOT adjust!
D = Set value adjustment for minimum temperature limitation.
E = Set value adjustment for maximum temperature limitation.
F = Jumper (MAX) must be SHORTED to activate maximum temperature limitation function. OPEN jumper deactivates the function.
G = Jumper (MIN) must be SHORTED to activate minimum temperature limitation function. OPEN jumper deactivates the function.
A red LED indicates that the heating elements are activated.
WARNING !
The PCB is at mains voltage level when the heater is connected to mains.
A = P
.
B = Cavalier, (Int/Ext), doit être en circuit FERMÉ.
C = Le réglage du potentiomètre d’ajustement est effectué lors de la fabrication du régulateur. Ne PAS changer le réglage!
D = Potentiomètre des valeurs prescrites pour fonction de limitation MINIMALE.
E = Potentiomètre des valeurs prescrites pour fonction de limitation MAXIMALE.
F = Cavalier, (MAX), doit être en circuit FERMÉ si la fonction de limitation MAXIMALE est active et en circuit OUVERT si la fonction n’est pas active.
G = Cavalier, (MIN), doit être en circuit FERMÉ si la fonction de limitation MINIMALE est active et en circuit OUVERT si la fonction n’est pas active.
otentiomètre interne de réglage de consigne. Est uniquement utilisé dans les appareils de chauffage de type -1PTU/-1PTUL
Une diode électroluminescente (LED) rouge indique que l'effet est dirigé vers l'extérieur.
REMARQUE !
La carte à circuit imprimé est conductrice de tension quand l’appareil de chauffage est sous tension.
A = S
B = Lenkin (Int/Ext) on oltava KIINNI.
C = Trimmeripotentiometrin asetukset on määritelty säätimen valmistuksen yhteydessä. ÄLÄ muuta asetuksia!
D = Asetusarvon säädin MIN-rajoitukselle.
E = Asetusarvon säädin MAX-rajoitukselle.
F = Lenkin (MAX) tulee olla KIINNI, kun MAX-rajoitusta aktivoidaan. Mikäli lenkki on AUKI, toiminto passivoituu.
G = Lenkin (MIN) tulee olla KIINNI, kun MIN-rajoitusta aktivoidaan. Mikäli lenkki on AUKI, toiminto passivoituu.
isäinen asetusarvopotentiometri. Käytetään vain lämmitintyypissä -1PTU/-1PTUL.
Punainen valodiodi (LED-valo) osoittaa, että teho ohjataan ulos.
HUOM !
Piirikortti on jännitteinen, kun lämmittimen syöttöjännite on kytkettynä.
Содержание CV Series
