Varta element 12 Скачать руководство пользователя | Manualshive

Страница: 38 / 111

background image

36

The housing and the battery module

•

a tested ABC fire extinguisher with a minimum volume capacity of 2 kg is to be carried.

•

pay attention to the symbols on the packaging.

•

Transport the parts in closed vehicles only.

•

the load is to be properly secured.

•

transport the battery module in its intended transport packaging only.

•

comply with the requirements pursuant to GGVSEB and ADR!

Use your personal protective equipment.

This reduces the risk of injuries during the mechanical works.

WARNING

Components are heavy.

This can lead to overburdened intervertebral discs, contusions and strains.

Carry out the works described in this chapter with 2 persons or suitable aids.

i

If a battery module is being replaced, it may be appropriate to request new dangerous
goods packaging, pack the battery module and have it collected by the supplier.

10.3

Packaging/transport control

DANGER

Installation of damaged components.

Danger to life.

Do not accept clearly damaged packaging.

Contact VARTA.

The storage cabinet and the battery module (individually packed) are delivered in separate and tested
packaging units on pallets. The installer assumes the disposal of the packaging. Please check the deliveries for
completeness and damage:

•

Should damage be recognisable on the packaging, please note this on the delivery documents and have
this confirmed by the driver by means of a signature.

•

Reject deliveries in heavily damaged packaging.

«
...
36
37
38
39
40
...
»

Содержание element 12
















































































































Отзывы:

Нет отзывов

Похожие инструкции для element 12

Бренд: Manfrotto Страницы: 2

Бренд: Samsung Страницы: 15

Бренд: Sami Страницы: 10

Бренд: Oki Страницы: 2

Бренд: OKIDATA Страницы: 16

Бренд: Zamel Страницы: 12

Бренд: K&M Страницы: 3

Multi Function Professional Puncher-A1

Бренд: Canon Страницы: 44

Southern Series

Бренд: Warmington Страницы: 2

Бренд: Naterial Страницы: 40

Бренд: Takara Belmont Страницы: 36

Бренд: Van Air Systems Страницы: 8

Бренд: Sierra Monitor Corporation Страницы: 1

Бренд: Dynojet Страницы: 2

Бренд: U.S. General Страницы: 4

Бренд: Pilz Страницы: 8

Бренд: moon Страницы: 4

Indoor Cycle Computer

Бренд: Waters Fitness Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды