Varec Network Adapter 4000 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 80

Varec Network Adapter 4000 Скачать руководство пользователя страница 37

27

4000

Maintenance and Troubleshooting

4 Maintenance and Troubleshooting

4.1

Maintenance

The Varec Model 4000 Advanced Technology Transmitter (ATT) is designed and

manufactured to provide accurate and reliable operation without a requirement for

regularly scheduled maintenance.

Due to the modular construction of the ATT, necessary repairs can be quickly and safely

accomplished.

Caution!

When performing service or repair of any kind on the ATT, follow all instructions rel-
ative to power on/off requirements. It is recommended that all necessary repairs be
performed by a factory trained service engineer.

4.2

Battery Replacement

The ATT contains a battery module to maintain incremental count information during

power outages. The battery shelf life is ten years and active life is 10 days. The ATT

monitors the battery voltage and will indicate a low battery status to the host computer.

The battery status can also be checked using the Handheld Terminal under the Summary

Menu.

The ATT may indicate a low battery condition for several reasons:

•

A brand new unit is shipped with the battery turned off.

•

The battery is really low or bad.

•

Someone has actually turned the battery off from the host computer or via the

Handheld Terminal if an extended power outage was anticipated.

•

The ATT may have automatically turned its battery off. This occurs to preserve the

battery if a power outage occurs for more than a 24 hour period.

Using a Handheld Terminal get into the Alter Mode of operation. Check if the battery is

really bad by calibrating the level. This turns on the battery circuitry automatically.

Perform an Exit and Save and log back in using the Display Mode. The Summary Menu

indicates the status of the battery as tested by the ATT.

Caution!

Power to the ATT must be off before attempting to replace the battery. Do not apply
power to the ATT until battery replacement is complete and all covers have been
replaced.

If the battery is still bad, perform the following to replace it:

1. Turn off all power to the ATT and remove the electronics' cover.
2. Locate the two covered batteries marked BT1 and BT2.
3. Slide off the battery cover.
4. Remove by sliding the batteries to the side and not straight out.
5. Replace with new batteries and replace battery cover.
6. Replace the ATT's cover
7. Turn the power to ATT back on.
8. Calibrate the level.

«
...
35
36
37
38
39
...
»

Содержание Network Adapter 4000

















































































Отзывы:

Нет отзывов