background image

OPERATION

NOTICE

CLEAN AFTER USE TO PREVENT PERMANENT

DAMAGE TO THE SPRAYER.

RETURNS NOT ACCEPTED & WARRANTY VOID IF SPRAYER IS NOT 

PROPERLY CLEANED IMMEDIATELY AFTER EVERY USE.

Prime/Spray Switch

The Prime/Spray Switch (F) 
toggles the unit between the 
priming mode and the spraying 
mode.

Trigger Lock

The Trigger Lock (S) prevents the 
trigger from being  accidentally 
actuated such as when the gun is 
dropped.

ALWAYS ENGAGE THE 
TRIGGER LOCK WHEN THE 
SPRAY GUN IS NOT IN USE.

Nozzle Spray Tip

The Nozzle Spray Tip (P) is 
removable and reversible to make 
cleaning and unclogging easier. 
Normal operation is with the arrow 
pointed outwards and away from 
the gun. Unclogging the nozzle is 
done by turning the Nozzle Spray 
Tip so the arrow is pointing 
inwards towards the gun.

Normal

Unclogging

Pressure Control Knob

The Pressure Control Knob (D) adjusts the pressure of the paint 
output at the Output Port (E). Turning the knob fully to the right 
(clockwise) adjusts the paint output to the maximum pressure 
for high pressure spraying. Turning the knob fully to the left 
(counter-clockwise) will reduce the paint output to the minimum 
pressure. Align the Pressure Control Knob indicator to the 
desired function as shown on the label (shown below).

High Spray

Low Spray

Prime/Clean

Roll

High Pressure Spray

Low Pressure Spray

Prime/Clean

Roller

Prime

Spray

Unlocked

Locked

8

V0.1

19802

Содержание 19802





























Отзывы: