VAF instruments OILCON MARK 6M Скачать руководство пользователя страница 102

Страница: 102 / 175

101

15.9 PNEUMATIC VALVE PROBLEMS

For repair procedures of pneumatic valves consult section 8.2.5.

15.9.1 Valve not functioning

Probable causes

Action

No air supply



Check the air supply unit regulator in the air supply line

to the valve, normally set to 4.0 bar (0.4 MPa).



Check all air connections for leakage.



Check the ship’s control air system.



Check the functioning of the solenoid valve. See

section 15.8.

Pneumatic valve failure



Check the actuator housing for leakage.

15.9.2 Valve gland leakage

Probable causes

Action

Worn gaskets



Damaged or worn gaskets or damage of the valve

gland.
Replacement of the gaskets is required.
The unit should be returned to a qualified service
centre for repair.

15.9.3 Valve leakage

Probable causes

Action

Leakage between the valve plug
and seat



Damaged or worn valve seat and plug.

Replacement of the valve seat and plug is required.
The unit should be returned to a qualified service
centre for repair.

Содержание OILCON MARK 6M
















































































































































































Результаты поиска

Содержание OILCON MARK 6M

Отзывы:

Похожие инструкции для OILCON MARK 6M

Бренды по названию

Популярные бренды

VAF instruments OILCON MARK 6M, Техническое руководство

Результаты поиска

Содержание OILCON MARK 6M

Отзывы:

Похожие инструкции для OILCON MARK 6M

Бренды по названию

Популярные бренды