VAF instruments OILCON MARK 6M Скачать руководство пользователя страница 44

Страница: 44 / 175

7 OPERATING

INSTRUCTIONS

7.1 LAYOUT OF THE MCU

Operation of the Oilcon

Oil Discharge Monitoring and Control System is controlled and recorded by

the MCU.
A representation of the control panel of the MCU, as fitted in the Cargo Control Room, is shown
below.

Figure 32: MCU layout

The MCU control panel contains the following:



Control key switch



USB

connector



RS-232 serial communication port



Reset

button



Touch screen panel

7.1.1 Control key switch

The control key switch is used to put the MCU in the following modes:



“Control” in this position the MCU is in the normal operational mode, automatically controlling

the ballast discharge system if automatic control is fitted.



“Off” in this position the display is blanked and the MCU goes to a quiescent state. Although

the MCU is in a quiescent state some inputs are still monitored and logged in the internal
memory.

NOTE:
Do not attempt to service the equipment in this mode, see section 8.



“Console” in this position the MCU is in normal operational mode but manual control of the

ballast discharge system is provided from the cargo console. There will be no alarms given
and some inputs are still monitored and logged in the internal memory.

Содержание OILCON MARK 6M
















































































































































































Результаты поиска

Содержание OILCON MARK 6M

Отзывы:

Похожие инструкции для OILCON MARK 6M

Бренды по названию

Популярные бренды

VAF instruments OILCON MARK 6M, Техническое руководство

Результаты поиска

Содержание OILCON MARK 6M

Отзывы:

Похожие инструкции для OILCON MARK 6M

Бренды по названию

Популярные бренды