Vacon DPD00109 Скачать руководство пользователя страница 15

Страница: 15 / 15

vacon

Keypad Remote Control Options

Step 12. Installing the Remote Keypad Assembly into the Host Enclosure (XRKMK only)

1. Position the remote keypad assembly into the enclosure prepared in

Step 1

(page 4).

2. Fasten the keypad module with the four (4) M5 x 12 screws provided, limiting torque to 26 in-lb maximum.

3. Secure the multi-conductor cable using the loop clamp on the lower portion of the keypad interface board.

You may need to loosen the cable clamp to install the cable in it.

4. Terminate the individual wires to TB1 and TB2 as in

Step 10

. For your convenience, TB1 and TB2 terminal

blocks are removable.

5. Route the cabling as needed to avoid any damage. Additional wire ties and tie bases are provided to allow

strain relief for the wire.

Figure 12: Installing the Remote Keypad Assembly into the Host Enclosure (XRKMK Option)

For detailed information on using the keypad, refer to the following documentation:

•

DPD 00088,

X4 AC Drive User’s Manual

•

DPD 00089,

X5 AC Drive User’s Manual

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание DPD00109
















Результаты поиска

Содержание DPD00109

Отзывы:

Похожие инструкции для DPD00109

Бренды по названию

Популярные бренды

Vacon DPD00109, Руководство по установке

Результаты поиска

Содержание DPD00109

Отзывы:

Похожие инструкции для DPD00109

Бренды по названию

Популярные бренды