Vacon DPD00109 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 15

background image

Keypad Remote Control Options

vacon

13

Step 9. AC Drive Preparation (XRKMK only)

1. Note the warnings and cautions on the unit and in the user’s manual.

2. Loosen the cover screws from the AC drive and open the cover.

3. Remove the four (4) screws that secure the keypad assembly and retain these for future use. These are M5 x

12 screws.

4. Unplug the ribbon cable and remove the keypad assembly. It will be re-used in

Step 12

.

5. Now go on to

Step 10

, beginning on

page 14

.

Figure 9: Removing the Keypad Assembly (XRKMK Option)

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

«
...
10
11
12
13
14
...
»

Содержание DPD00109
















Отзывы:

Нет отзывов

Похожие инструкции для DPD00109

Бренд: Bartlett Страницы: 30

Бренд: Garmin Страницы: 4

coviva Smartbox TKP100A

Бренд: hager Страницы: 4

Бренд: Vag Страницы: 12

Бренд: Bartlett Страницы: 7

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 20

Бренд: Yamaha Страницы: 2

Бренд: RADEMACHER Страницы: 68

Бренд: Jäger Страницы: 18

Бренд: micro-trak Страницы: 44

Бренд: Mosa Страницы: 28

Бренд: NXP Semiconductors Страницы: 39

Бренд: CP Electronics Страницы: 12

Бренд: NCE Страницы: 4

RISC Module SOM-A2552

Бренд: Advantech Страницы: 40

Бренд: Calex Страницы: 16

Бренд: Etherma Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды