V2 ZORUS, Руководство пользователя

Страница: 15 / 38

ENGLISH
- 47 -
4.11 - LOCK
An electric lock can be assembled on the gate, to ensure a good
closing of doors. Make use of a 12V lock.
Connect lock cables to terminals
K4
and
K5
of the control unit.
K1 K2 K3 K4 K5 K6 K7 K8 K9
K10
J1 J2 J3 J4 J5 J6 J7 J8 J9
A1 A2
B1 B2
COUR
TESY LIGHT
CONT
AC
T
RECEIVER
LOCK
LAMP 24V
-3W
+24VDC
COM (-)
+24VDC
(Photo
TX / Edge
Test)
ST
AR
T
P.
ST
OP
COM
PHO
TO
PHO
TO-I
EDGE1 EDGE2
COM
BATTERY
+
ST
AR
T
ANT
M2
M1
Max 500mA
24 Vdc
POWER SUPPLY
24Vdc
24Vdc
Control unit model: PD12
4.12 - EXTERNAL AERIAL
We suggest to use the external aerial (model: ANS433) in order to
guarantee the maximal range.
Connect the antenna hot pole to terminal A2 (ANT) of the
control unit and the braiding to terminal
A1 (ANT-)
.
NOTE : using the LUMOS flashing light with built-in antenna,
connect the terminal 3 of the flashing light to the terminal
A2 (ANT) of the control unit and the terminal 4 of the flashing
light to the terminal
A1 (ANT-)
of the control unit PD12
K1 K2 K3 K4 K5 K6 K7 K8 K9
K10
J1 J2 J3 J4 J5 J6 J7 J8 J9
A1 A2
B1 B2
COUR
TESY LIGHT
CONT
AC
T
RECEIVER
LOCK
LAMP 24V
-3W
+24VDC
COM (-)
+24VDC
(Photo
TX / Edge
Test)
ST
AR
T
P.
ST
OP
COM
PHO
TO
PHO
TO
-I
EDGE1 EDGE2
COM
BATTERY
+
ST
AR
T
ANT
M2
M1
Max 500mA
24 Vdc
POWER SUPPLY
24Vdc
24Vdc
Control unit model: PD12
4.13 - PLUG IN RECEIVER
PD12 control unit is suitable for plugging in a MR2 receiver having
a high-sensitivity super-heterodyne architecture.
m
WARNING: it is necessary to turn off the control unit
power before doing the operations mentioned here below.
Pay attention to the way you connect the removable
modules.
MR2 module receiver is provided with 4 channels and each of
them is suitable for a command of PD12 control unit:
• CHANNEL 1
g
START
• CHANNEL 2
g
PEDESTRIAN START
• CHANNEL 3
g
STOP
• CHANNEL 4
g
COURTESY LIGHT
NOTE: Before programming 4 channels and function
logics read carefully the instructions of MR2.
4.14 - ADI INTERFACE
The ADI (Additional Devices Interface) interface of the control unit
PD12 allows the connection to V2 optional modules.
Refer to V2 catalogue or to the technical sheets to see which
optional modules with ADI interface are available for this control
unit.
NOTE Please read the instructions of each single module to
install the optional modules.
4.15 - POWER SUPPLY
The control unit must be fed by a 230V 50Hz electric line,
protected by a differential magnetothermal switch complying with
the law provisions in force.
Connect the power supply wires to terminals L and N on the
board located next to the transformer.
Connect the earth cable to terminal
Fuse: 5A
L
N
4.16 - BATTERY POWER
In the case of an electricity black-out, the device may be powered
using a battery pack (accessory code 161212).
The battery pack should be housed in the specific seating, as
shown in the figure.
Connect the battery pack connecter to the BATTERY terminals on
the control unit.
K1 K2 K3 K4 K5 K6 K7 K8 K9
K10
J1 J2 J3 J4 J5 J6 J7 J8 J9
A1 A2
B1 B2
COUR
TESY LIGHT
CONT
AC
T
RECEIVER
LOCK
LAMP 24V
-3W
+24VDC
COM (-)
+24VDC
(Photo
TX / Edge
Test)
ST
AR
T
P.
ST
OP
COM
PHO
TO
PHO
TO-I
EDGE1 EDGE2
COM
BATTERY
+
ST
AR
T
ANT
M2
M1
Max 500mA
24 Vdc
POWER SUPPLY
24Vdc
24Vdc
Control unit model: PD12