Uwatec Aladin TEC 3H Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 79

background image

52

CCR Diving

4.11 CCR Diving

Closed Cricuit Diving

Switching range
SP1 to SP2

Switching range
SP2 to SP1

Time

Depth

SP2

SP1/2

SP1

NOTE:

The following chapter deals with the characteristics of CCR diving.

Aladin TEC 3H enables you to switch between 2 different ppO

2

settings during the same CCR dive

(setpoints SP1 and SP2).
In addition a Bail-Out gas mixture can be used which allows to switch from CCR diving to open circuit
diving.

4.11.1 Preparation for the CCR dive

You have to check the settings of Aladin TEC 3H especially before the first dive. All settings can be
checked and changed directly at Aladin TEC 3H or via LogTRAK.

Switching the CCR option on and off

In order to enable CCR diving you must turn on the CCR option in the SET 1 menu ->68.

4.11.2 Setting the ppO

2

and gas mixture

WARNING

Before every dive and after changing the tank, make sure that the settings for the gas mixture correspond with
the current mixture used. An incorrect setting causes Aladin TEC 3H to miscalculate this particular dive. If the
fraction of oxygen is set too low this can lead to oxygen poisoning without warning. If the value is set too high
decompression sickness may occur. Inaccuracies in the calculations are carried over to repetitive dives.

Setting the Setpoints SP1 and SP2

During dives with two setpoint settings the SP1 contains the lower fraction of oxygen. Aladin TEC 3H
will only accept settings corresponding with this order.

To set the setpoints SP1 and SP2, Aladin TEC 3H must be in user mode (time of day display).

Procedure:
1. Push

or

until the SP1 menu appears.

2. Confirm that you wish to change the SP1 settings by pushing

.

«
...
50
51
52
53
54
...
»

Содержание Aladin TEC 3H
















































































Отзывы:

Нет отзывов

Похожие инструкции для Aladin TEC 3H

Бренд: Fender Страницы: 20

Бренд: Laney Страницы: 7

Бренд: Laney Страницы: 24

Бренд: Laney Страницы: 6

Бренд: Van Walt Страницы: 12

Бренд: VELOCICALC Страницы: 10

Бренд: DGH Страницы: 87

Бренд: Bamo Страницы: 17

Бренд: LumaSense Страницы: 23

BML-S1G0-Q71 Series

Бренд: Balluff Страницы: 20

Бренд: Trotec Страницы: 14

Бренд: Sonel Страницы: 26

Бренд: IDT Страницы: 20

Бренд: Vega Страницы: 44

Бренд: Amrutha Technologies Страницы: 22

Бренд: Straightpoint Страницы: 24

Бренд: AL Страницы: 2

Бренд: HEIDENHAIN Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды