Uwatec Aladin TEC 3H Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 79

background image

45

ENGLISH

Diving with 2 or 3 gas mixtures

4.10 Diving with 2 or 3 gas mixtures

Bottom mix, gas 1

Time

Switching
depth
(MOD
gas d)

Switching
depth
(MOD
gas 2)

Travel mix, gas 2

Depth

Deco mix (gas d)

The following chapter deals with the characteristics of diving with 2 or 3 gases. In case of using 2

gas mixtures (gas 1 and d), just ignore the parts describing the gas 2.

When diving with multiple gas mixtures, the tank pressure at TEC 3H display remains always the

one where it is connected by the hose.

Aladin TEC 3H enables you to use up to 3 different Nitrox mixtures during the same dive. Tank 1
contains the bottom mix (gas 1), tank 2 the travel mix and tank d contains the deco mix (gas d).

Switching the deco gas option on and off

In order to enable two- or three gas diving you must turn on the deco gas option in the SET 1 menu
->69.

Setting the gas mixture and the depth for changing the gas mixture

2

1

d

O

2

fraction

Range of O

2

fraction

100%

21%

During dives with 2 or 3 gas mixtures the bottom mix (gas 1) contains the lowest and gas d the highest
fraction of oxygen.
Aladin TEC 3H will only accept settings corresponding with this order.

WARNING

For gas mixtures having an oxygen percentage of 80% or greater the ppO

2

is fixed at 1.6 bar and cannot be altered

in any way.

«
...
43
44
45
46
47
...
»

Содержание Aladin TEC 3H
















































































Отзывы:

Нет отзывов

Похожие инструкции для Aladin TEC 3H

Workstation Monitor 724

Бренд: 3M Страницы: 21

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 24

Бренд: 3M Страницы: 2

SoundPro SE Series

Бренд: 3M Страницы: 293

Бренд: C-LOGIC Страницы: 4

Бренд: C-lock Страницы: 32

Бренд: C-LOGIC Страницы: 12

Бренд: Danfoss Страницы: 6

Бренд: Macnaught Страницы: 4

POCKET COLORIMETER II

Бренд: Hach Страницы: 188

Бренд: La Crosse Technology Страницы: 8

Бренд: Parkside Страницы: 94

Бренд: Kobold Страницы: 55

Бренд: Richie Kotzen Страницы: 12

Бренд: Peavey Страницы: 4

Бренд: Sper scientific Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды