Uwatec Aladin TEC 3H Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 79

background image

17

ENGLISH

System and operation / SOS

2.13 Switching off the display

From the

time of day display

you can switch off Aladin TEC 3H

by pushing

.

On the surface Aladin TEC 3H switches off automatically after 3 minutes without operation.

2.14 Alarm clock

The alarm clock goes off only at the surface.
If the alarm clock is "on", the time of day display shows

.

When alarm is triggered:

flashes and special attention beeps are played for 30 seconds or until

the user presses a button.

Setting the alarm clock: ->72 ("set 2")

3

SOS MODE

Activation: automatic
If the diver remains above a depth of 0.8m (3ft) for more than three minutes
without observing a prescribed decompression stop, the computer will
automatically switch into SOS mode after the dive.

Push

to see the "SOS" sign and the remaining length of the SOS mode.

The dive will be entered in the logbook with "SOS".

The SOS mode will be unlocked after 24 hours.

While in SOS mode, the computer cannot be used for diving.

Diving within 48 hours after the end of an SOS mode will result in shorter no stop times or longer
decompression stops.

WARNING

•

Serious injury or death may result if a diver does not seek immediate treatment should any
signs or symptoms of decompression sickness occur after a dive.

•

Do not dive to treat symptoms of decompression sickness!

•

Diving in SOS mode is extremely dangerous and you must assume full responsibility for
such behavior. Scubapro will assume no liability.

Time remaining until

SOS mode switches

off automatically

«
...
15
16
17
18
19
...
»

Содержание Aladin TEC 3H
















































































Отзывы:

Нет отзывов

Похожие инструкции для Aladin TEC 3H

Бренд: Major tech Страницы: 8

Бренд: Waltron Страницы: 25

Бренд: janitza Страницы: 12

Electone B-20CR

Бренд: Yamaha Страницы: 16

Бренд: janitza Страницы: 48

50KW POWER WEDGE

Бренд: YORKVILLE Страницы: 9

Бренд: YOSensi Страницы: 3

Бренд: Yamaha Страницы: 12

Бренд: PITSID Страницы: 22

Бренд: Swan Analytical Instruments Страницы: 102

Microlog GX Series

Бренд: SKF Страницы: 342

Бренд: Aktobis Страницы: 7

IMI SENSORS 604B11

Бренд: PCB Piezotronics Страницы: 19

Ocean Optics HR2000 Series

Бренд: Halma Страницы: 42

Бренд: sebaKMT Страницы: 131

Бренд: Princeton Instruments Страницы: 28

Бренд: Oberheim Страницы: 41

Бренд: Newton Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды