Uwatec Aladin TEC 3H Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 79

background image

27

ENGLISH

Functions during the dive

• Aladin TEC 3H will display CNS O

2

% values exceeding 199 %

with 199 %.

•

Aladin TEC 3H displays CNS O

2

% values above 50%.

4.4.10 Nitrogen loading bar graph

The nitrogen loading bar gives a graphical representation of how close to decompression you are. As
you absorb nitrogen during the dive, more and more segments of the bar will light up. Depending on
your depth, the segments can light up more or less rapidly.

1-3 segments (green
area):
you are safely within the
no-stop range.

4-5 segments (yellow
area):
you are approaching
decompression. When
the no-stop time drops
below 3 minutes the
5 segments will start
flashing.*

6 segments (red
area): you now
have mandatory
decompression
obligation(s) which you
must observe before
reaching the surface.

* Depending on your profile, the no-stop time may drop below 3 minutes before the upper 5 segments are lit. In this case, only those segments
that are lit will flash.

If you have entered decompression, the 6th segment will turn off as soon as you complete your last
decompression obligation to indicate that you are no longer in decompression.

4.4.11 Decompression information

NO STOP and the no-stop time (minutes) are displayed if no decompression stops are necessary.

F

• No-stop display "99:" means remaining time of 99 minutes or

more.

• No-stop time is influenced by the water temperature.

WARNING

If no-stop time drops below 3 minutes, an audible attention signal is
activated, the no-stop value and the nitrogen loading bar begin to
flash. If no-stop time is less than 1 minute, the no-stop display shows
the flashing value "0".
In order to prevent a decompression dive, ascend slowly until the
no-stop time is 5 minutes or more.

WARNING

Dives that require decompression stops are not recommended.

No-stop time

Nitrogen loading bar

4s

No-stop time less

than 1 minute

«
...
25
26
27
28
29
...
»

Содержание Aladin TEC 3H
















































































Отзывы:

Нет отзывов

Похожие инструкции для Aladin TEC 3H

Бренд: Kawai Страницы: 2

Бренд: Datron Страницы: 197

Бренд: YOKOGAWA Страницы: 3

Бренд: Oceanic Страницы: 17

Бренд: Hammond Organ Страницы: 25

Бренд: Hammond Organ Страницы: 87

Бренд: Mahr Страницы: 384

Бренд: SAGEMCOM Страницы: 33

Clavinova CVP-805

Бренд: Yamaha Страницы: 112

Clavinova CLP-270

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 3

Бренд: Gibson Страницы: 1

Бренд: Johnson & Associates Страницы: 33

Бренд: PCE Health and Fitness Страницы: 11

SensoControl Serviceman SCM-150 Series

Бренд: Parker Страницы: 39

iTrans 77023554

Бренд: Industrial Scientific Страницы: 94

Бренд: Water I.D. Страницы: 56

Бренд: Meec tools Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды