Uwatec Aladin TEC 3H Скачать руководство пользователя страница 62

Страница: 62 / 79

Dive planner

DIVE PLANNER

PLn: Aladin TEC 3H has a dive planner which allows the planning of no-stop dives and decompression
dives.
Basis of the planning:

• selected fraction of oxygen and MOD

• selected water type

• selected MB level

• water temperature of the most recent dive

• altitude range (if any)

• status of saturation at the time the dive planner is selected

• assuming a normal workload of the diver and observance of

the prescribed ascent rates

•

assumption: the change to gas 2/d is performed at the selected

MOD of gas 2/d.

• CCR: assumption: the gas changes are performed at the selected

setpoints (SP1 and SP2).

5.1 Planning a no-stop dive

To select the dive planner Aladin TEC 3H must be in user mode (

time of day display

). Push

until the symbol for the dive planner PLn appears. (The dive planner cannot be selected in

gauge mode.)

The no-dive warning and its duration are displayed if Aladin TEC 3H detects an increased risk due

to the accumulation of microbubbles.

Input of the surface interval

by pushing

Enter the
dive planner

No-stop time

Set desired depth

(

and

)

CNS O

Dive planner icon

Select dive planner

until PLn

if rep. dive

No-dive warning
(Do Not Dive)

Duration of the
warning

Содержание Aladin TEC 3H
















































































Результаты поиска

Содержание Aladin TEC 3H

Отзывы:

Похожие инструкции для Aladin TEC 3H

Бренды по названию

Популярные бренды

Uwatec Aladin TEC 3H, Руководства пользователя

Результаты поиска

Содержание Aladin TEC 3H

Отзывы:

Похожие инструкции для Aladin TEC 3H

Бренды по названию

Популярные бренды