Uwatec Aladin TEC 3H Скачать руководство пользователя страница 50

Страница: 50 / 79

Diving with 2 or 3 gas mixtures

Changing the gas mixture

DEPTH

DIVE TIME

Switch depth

Switch to gas d

MOD gas d

After immersion, Aladin TEC 3H automatically selects gas 1.

WARNING

When during an ascent a switch depth is reached (MOD gas 2 or gas d), an audible warning goes off and “GAS 2”
/ “GAS d”, its MOD and O

% blink for 30 seconds.

Procedure:
1. Switch to the regulator with gas 2 / gas d and start breathing.
2. Confirm the change by pressing

within 30 seconds. “GAS 2” / “GAS d” and the oxygen

fraction of gas 2 / gas d is displayed for 5 seconds without blinking.

DEPTH

DIVE TIME

Change to gas d confirmed

To interrupt the switch process at any point, press

so many times until the original gas is again

active; or do not confirm the gas change process.

No change of gas mixture:

If a diver fails to confirm the change of gas mixture or interrupts the switching procedure by pressing

, Aladin TEC 3H displays “GAS 1” / “GAS 2”, the MOD and the oxygen fraction for 5 seconds.

Aladin TEC 3H continues to calculate with gas 1 / gas 2 only and adapts the decompression calculation
accordingly.

Содержание Aladin TEC 3H
















































































Результаты поиска

Содержание Aladin TEC 3H

Отзывы:

Похожие инструкции для Aladin TEC 3H

Бренды по названию

Популярные бренды

Uwatec Aladin TEC 3H, Руководства пользователя

Результаты поиска

Содержание Aladin TEC 3H

Отзывы:

Похожие инструкции для Aladin TEC 3H

Бренды по названию

Популярные бренды