24
Concord
4.
You hear a short status message, such as, “System is
OK.”
5.
Proceed with system commands.
Codes with Remote Access Capability
The ability to access the system from off-site is a code
attribute see “Assigning Code Attributes” on page 11.
Check the User Sheets in Appendix A to see which access
codes have the ability to operate the system from off-site.
Touchtone Phone System Operation
Phone operation of your system involves 2 steps:
Sending a Police Panic Alarm
Your system can be set up so that you can send a Police
panic alarm from a Touchtone phone. If your system is set
up to send a Police panic alarm:
❑
Use the
‚
, regardless of your phone command key.
❑
Do not wait more than two seconds between key-
presses. Continue pressing
‚
even if you hear the
system voice interrupt with a system status.
❑
Police panic alarms can be activated from a Touch-
tone phone on the premises only. The alarm cannot be
activated from an off-site phone.
Step 1. Use a Touchtone phone to access the system.
Local Phone
Access
Pick up the phone. Within 5 seconds of
picking up the phone receiver, enter the
command prefix.
Remote Phone
Access
Use the Ring-Hang-Ring or the Twelve-
Ring method to get the system to answer the
call.
Then enter
ƒ
(or designated phone prefix)
+
CODE
Step 2. Enter the command.
Disarm the system
ƒ
+
1
+
CODE
Arm to Level 2*
ƒ
+
2
+
CODE
Arm to Level 3*
ƒ
+
3
+
CODE
Send a Police panic
alarm
‚
+
‚
+
‚
+
‚
+
‚
+
‚
(Available from on-site only.)
Arm system with
No Delay*
ƒ
+
2
+
CODE
+
4
or
ƒ
+
3
+
CODE
+
4
Arm to enable
Latchkey*
ƒ
+
2
+
CODE
+
6
or
ƒ
+
3
+
CODE
+
6
Arm system with
exit lights off*
ƒ
+
2
+
CODE
+
0
or
ƒ
+
3
+
CODE
+
0
Bypass a sensor
Indirectly: Arm
ƒ
+
ƒ
Directly:
ƒ
+
ƒ
+
CODE
+ Sensor
Number
Arm silently*
ƒ
+
5
+
2
+
CODE
or
ƒ
+
5
+
3
+
CODE
Turn all lights on/
off
ƒ
+
0
+
0
Turn specific lights
on/off
ƒ
+
0
+ Light number (1–9)
Cancel an
accidental alarm
ƒ
+
1
+
CODE
Check the system
status
ƒ
+ for short status
ƒ
+
‚‚
for full status
Turn Chime on/off
ƒ
+
7
+
1
Turn Energy Saver
on/off
ƒ
+
7
+
2
Disable local phone
access
ƒ
+
7
+
3
(on-site only) or
Wait 5 seconds after picking up a local
phone.
Check alarm
memory
ƒ
+
7
+
6
Activate Outputs
ƒ
+
7
+
7
+
Output number (1–6)
* If Quick Arm feature is on, access code is not required.
See page 6 for more information.
Step 2. Enter the command.
Phone Questions?
What if someone calls while I’m operating the
panel?
If the phone rings while you’re using it to operate
the system, you’ll hear one long beep for each ring
from interior speakers and phones. You can answer
the call by simply hanging up on the system, then
answering the call as you normally would.
You’ll have to initiate another session to resume
operation.
Can I control the system while I’m talking on the
phone?
No.
How do I perform other phone operations
without commanding my security system?
You can use your phone for transactions such as
banking from home by temporarily disengaging
phone control to your security system. The com-
mands described below work for one call at a time.
To disengage local phone control:
❑
Enter
ƒ
+
7
+
3
.
The system responds by returning a dial tone.
❑
Pick up the phone receiver and wait 5 seconds
before dialing any numbers. After the 5 second
period, the system disables local phone control
and ignores phone commands.
