Utax LP 3036, Инструкция по эксплуатации

Страница: 82 / 113

Chapter 5 Paper Selection
5-3
Wavy or tight edges can cause misfeeding and alignment anom-
alies. The moisture content of the paper should be 4 to 6%. To
ensure the proper moisture content, it is important to store the
paper in a controlled environment. Some tips on moisture control
are:
• Store paper in a cool, dry location.
• Keep the paper in its wrapping as long as possible. Rewrap
paper that is not in use.
• Store paper in its original carton. Place a pallet, etc., under the
carton to separate it from the floor.
• After removing paper from storage, let it stand in the same
room as the printer for 48 hours before use.
• Avoid leaving paper where it is exposed to heat, sunlight, or
damp.
Paper Grain
When paper is manufactured, it is cut into sheets with the grain
running parallel to the length (long grain) or parallel to the width
(short grain). Short grain paper can cause feeding problems in
the printer. All paper used in the printer should be long grain.
Other Paper Properties
Porosity:
Refers to the density of the paper structure; that is,
how openly or compactly the fibers are bonded.
Stiffness: Limp paper can buckle inside the printer, while paper
that is too stiff may bind. Either way the result is a paper jam.
Curl: Most paper has a natural tendency to curl in one direction.
The paper should be loaded so that the natural curl is downward,
to counteract the upward curl imparted by the printer. Printed
sheets will then come out flat. Most paper also has a top and bot-
tom surface. Loading instructions are usually given on the paper
package.
If the paper is considerably curled in one direction, e.g. when the
paper was used to print on one side, try to roll the paper in the
opposite direction to counteract the curl. Printed sheets will then
come out flat.
Electrostatic properties: During the printing process, the paper
is electrostatically charged to attract the toner. The paper must
be able to release this charge so that printed sheets do not cling
together in the output tray.
Whiteness: The contrast of the printed page depends on the
whiteness of the paper. Whiter paper provides a sharper, bright-
er appearance.
Quality control: Uneven sheet size, corners that are not
square, ragged edges, welded (uncut) sheets, and crushed edg-
es and corners can cause the printer to malfunction in various
ways. A quality paper supplier should take considerable care to
ensure that these problems do not occur.
Packaging: Paper should be packed in a sturdy carton to pro-
tect it from damage during transport. Quality paper obtained
from a reputable supplier is usually properly packaged.
This section explains printing on special paper. The page printer
can use the following types of special paper. In this case, set the
media type according to the table below.
When using the above types of paper, be sure to use products
that are specified for use with photocopiers and/or page printers.
Feed paper other than colored paper or pre-printed paper from
the MP (multi-purpose) tray. Use paper that is sold specifically
for use with copiers (heat-fusing type). Label paper and enve-
lopes should not be placed in the cassette; they must be fed
manually and delivered in the face up stack.
Since the composition and quality of special paper vary consid-
erably, special paper is more likely than white bond paper to give
trouble during printing. No liability will be assumed if moisture,
etc., given off in printing on special paper causes harm to the
machine or operator.
Before purchasing any type of special paper, test a sample on
the printer and check that print quality is satisfactory.
Specifications for each type of special paper are given below.
Transparency must be able to withstand the heat of fusing during
the printing process. It should satisfy the conditions given in the
table below.
To avoid trouble, transparency must be delivered face-up.
If transparency jams frequently, pull the top of the sheet very
gently as it leaves the printer.
NOTE
2. Special Paper
Paper type to be used Media type to be selected
Colored paper Color
Preprinted paper Preprinted
Overhead projector
transparencies Transparency
Postcards Cardstock
Envelopes Envelope
Label Labels
NOTE
2.1 Transparency (Overhead Projection Film)
Item Specification
Tolerance of heat Must tolerate at least 190 °C
(374 °F)
Thickness 0.100 to 0.110 mm (3.9 to 4.3
mils)
Material Polyester
Dimensional accuracy ±0.7 mm (±0.0276 inches.)
Squareness of corners 90° ± 0.2°