Chapter 3 Using the Operator Panel
3-18
Maximum Space Assigned to Virtual Mailboxes (VMB)
This changes the hard disk space for virtual mailboxes. You can
change the maximum space from 0 to 9999 (megabytes). The
actual maximum size depends on the size of free hard disk
space, however. The default size is 1/6 of the total hard disk
space, rounded off in unit of 50 MB. For example, if the total
hard disk space is 3.2 GB, the default size is 500 MB.
Press the
MENU
key.
Press the
3
or
4
key until
e-MPS >
appears.
Press the
2
key.
Press the
3
or
4
key and select
>e-MPS Configu-
ration >
.
Press the
2
key.
Press the
3
or
4
key and select >>VMB Size.
To change the maximum size, press the
ENTER
key.
The message display shows a blinking cursor (
_
).
Press the
3
or
4
key to increase or decrease, respec-
tively, the value at the blinking cursor. Use the
2
and
1
keys to move the cursor right and left.
When the desired size is displayed, press the
ENTER
key.
Press the
MENU
key to exit the menu selection.
2.2.4 Changing the Interface Parameters
The printer is equipped with both a parallel and serial interface
or a network interface. Various printing environment parameters
such as the default emulation can be changed independently on
different interfaces by using the printer’s menu selection sys-
tem. Select the interface to apply the changes in the procedure
described below.
This interface selection described below does not select which
interface data will be received from. The printer automatically
selects an interface data to be received.
Changing Parallel Interface Modes
The parallel interface mode of this printer supports a bi-direction-
al/high-speed mode. Normally, this interface is used under the
default setting Nibble (high). For details, see
Appendix C Host
Computer Interface
. After setting the interface, be sure to reset
the printer or turn the power off at least once. The new setting
will be enabled thereafter.
Press the
MENU
key.
Press the
3
or
4
key repeatedly until
Interface >
appears. One of the interface names shown below ap-
pears, indicating the current interface.
Parallel
(default)
Serial
Network
Option
(only when an optional network interface
card is installed)
Press the
ENTER
key. A blinking question mark (
?
) ap-
pears.
If
Parallel
is not displayed, press the
3
or
4
key
repeatedly until
Parallel
appears.
Press the
ENTER
key again.
Press the
2
key. The message display changes to the
communication mode menu.
Press the
ENTER
key. A blinking question mark (
?
) ap-
pears.
e-MPS >
>e-MPS >
Configuration
>>VMB Size
0500MB
>>VMB Size
0500MB
1
2
3
4
5
6
7
8
9
10
NOTE
Interface >
?Parallel
>Parallel I/F
?Nibble (high)
1
2
3
4
5
6
Содержание LP 3036
