Material binds blade when ripping.
Fence not aligned with blade. Check and ad-
just fence.
Warped wood. Select another piece of wood.
Excessive feed rate. Reduce feed rate.
Splitter not aligned with blade. Align splitter
with blade.
Saw makes unsatisfactory cuts.
Dull blade. Sharpen or replace blade.
Blade mounted backwards. Properly mount
the blade.
Gum or pitch on blade. Remove blade and
clean.
Incorrect blade for cut. Change blade to co-
rrect type.
Gum or pitch on table. Clean table.
Blade does not come up to speed.
Extension cord too light or too long. Replace
with adequate size cord.
Low shop voltage. Contact your local electric
company.
Motor not wired for correct voltage. Refer to
motor junction box.
Saw vibrates excessively.
Stand on uneven floor. Reposition on flat, level
surface.
Damaged saw blade. Replace saw blade.
Bad V-belts. Replace V-belts.
Bent pulley. Replace pulley.
Improper motor mounting. Check and adjust
motor.
Loose hardware. Tighten hardware.
Loose set screw in pulley. Tighten set screw.
Rip fence binds on guide rails.
Guide rails or extension wing not installed co-
rrectly. Reassemble guide rails, refer to fence
manual.
Guide of rip fence not adjusted properly. Ad-
just guides, refer to fence manual.
Material kicked back from blade.
Rip fence out of alignment. Align rip fence
with miter slot and blade.
Splitter not aligned with blade. Align splitter
with blade.
Feeding stock without rip fence. Install and use
rip fence.
Splitter not in place. Install and use splitter
(with guard).
Dull blade. Replace blade.
Letting go of material before it is past blade.
Push material all the way past blade before re-
leasing work.
Anti-kickback fingers dull. Replace or sharpen
anti-kickback fingers.
Blade does not raise or tilt freely.
Sawdust and debris in raising and tilting me-
chanisms. Clean and grease.
Dimensions
Lenght / Width / Height
Foot print (lenght/width)
Motor
Power/Voltage/Amperage
Phases
Blade information
Maximum blade diameter
Riving knife thickness
Blade body thickness
Blade kerf thickness
Max. width of dado
Blade tilt (left)
Arbor size
Arbor speed
Cutting capacity
Max. depth of cut at 90˚
Max. depth of cut at 45˚
Max. rip to right of blade
Max. rip to left of blade
Table Information
Lenght/Width/Thickness
Floor to table height
Distance from the front of
table to center of blade
Distance from the front of
table to blade max. cut
Fence information
Lenght/Width/Height
Miter gauge info
Slot type
Width/Height of slot
Additional information
Dust port size
Weight
82"x 41"x 40"
(208,2 cm x 104,1 cm x 101,6 cm)
20"x 20" (50,8 cm x 50,8 cm)
4 100 W 220 V ~ 14,4 A
3 ~
10" (255 mm)
0,1" (2,5 mm)
0,071"- 0,094" (1,8 mm - 2,4 mm)
0,102"- 0,126" (2,6 mm - 3,2 mm)
13/16" (20,6 mm)
0 - 45˚
5/8" (15,9 mm)
4 300 r/min
3 1/8" (79,3 mm)
2 3/16” (55,5 mm)
50" (127 cm)
12" (30,5 cm)
20"x 27"x 1 1/2"
(50,8 cm x 68,6 cm x 3,8 cm)
34" (86,3 cm)
17 1/4" (43,8 cm)
12 1/4” (31,1 cm)
48"x 4 1/8"x 2 1/2"
(121,9 cm x 10,4 cm x 6,3 cm)
“T”
3/4"x 3/8" (19 mm x 9,5 mm)
4" (10,1 cm)
267,6 kg (590 lb)
25
E N G L I S H •
User’s manual
TECHNICAL DATA
SM1113 manual.indd 25
03/08/16 4:21 p.m.