Uponor KaMo Combi Port BASE XU, Инструкция по установке и эксплуатации

Страница: 4 / 36

4 l Uponor Combi Port BASE XU l Installation manual
In the case of installations in the public sector (multi family homes,
hotels, retirement homes, hospitals, sports halls, etc.) care must be
taken to ensure that the heated drinking water temperature does not
fall below 60°C and the circulating water re-entering the unit reaches
a minimum temperature of 55°C. This requires accurate calculation
and precise adjustment of the circulating line.
The system is maintained in compliance with DIN EN 806-5 or, outside
Germany, in accordance with national regulations or standards.
Use-related wear of wearing parts, such as pumps, built-in valves
(moving parts, PM valves, etc.) are not considered as defects.
We recommend a maintenance cycle especially for example for the
built-in heat exchanger (test, dirt, sludge, lime), PM valve (functional
WHVWGLUW¿OWHUVKXWRႇYDOYHVIXQFWLRQDOWHVWYDOYHVVXFKDVD
thermostatic lead module, thermostatic hot water temperature limiter,
]RQHYDOYHVLQMHFWLRQYDOYHGLႇHUHQWLDOSUHVVXUHUHJXODWRUSXPS
volume measuring unit, thermal premixer or other parts.
5 Please instruct the system users properly and provide them with
these installation and operating instructions together with the
inventory documents.
Please check that the units are complete. Any screws that
are loosened during transport should be retightened.
In the event of leaks that occur during the pressure test, be
VXUHWRGHSUHVVXULVHWKHXQLWEHIRUHUHSODFLQJDQ\DႇHFWHG
components.
Never remove individual parts of the unit (or any other built-in
components) while the system is still under pressure (risk of injury).
If you have any questions about correct operation or function,
please contact your supplier. Of course you are also welcome
to contact us directly anytime.
1.1 Validity of the instructions
These installation and operating instructions apply exclusively to
the manufacturer’s unit. The type can be found on the ID plate.
The ID plate is located on the base plate of the unit. The ID plate
contains the following information.
• Sales
• Created by
• Device type
• Technical data
• Year built
• Serial number
• Order number
• Production location
1.2 ID plate (example)
Device type: Combi Port BASE XU
Hz-VI temperature: max. 95°C
7::ÀRZUDWH Exchanger type 1; 15 l/min
Pressure level Hz/TWW: PN 10/PN 6
Year built: 2020
Serial number: D-10-0026036
Order number: 102628
Made in Germany
1.3 Related documents and regulations
• Additional documents are valid in conjunction with
these installation and operating instructions.
• When carrying out service work on the unit, it is essential to
observe all instructions for supplementary components and
components of the heating system.
• In all service work pay attention to:
- the recognised technical rules for safe and
professional operations
- the statutory regulations for accident prevention
- the statutory environmental protection regulations
- the stipulations of employer’s liability insurance associations
- the relevant safety conditions of the DIN, EN, DVGW, DWGW,
VDE and AGFW standards
- the relevant national and EU regulations for other countries
DQGWKHUHOHYDQWVSHFL¿FDWLRQVIRUWKHUHFRJQLVHGUXOHV
of engineering
1.4 Document retention
• You should keep these instructions and all other applicable
documents in a safe place, so that they are always available.
• Make sure to hand over all the documents to the operator.
1.5 Correct operation
The heat interface unit is intended exclusively for drinking water
heating, control of the downstream domestic heating system and
the measurement of heating energy and cold water consumption
for an apartment or similar unit.
Any other or further use is considered improper use. The
manufacturer/supplier is not liable for resulting damages. The risk
is borne solely by the user. Intended use also includes observance
of all relevant documents and compliance with the inspection and
maintenance conditions.
Under no circumstances should you deviate from the values given
in the technical data.
1.6 Personnel and qualifications
The heat interface unit may be operated by the operator or by
personnel authorised by the operator. Service work (assembly,
commissioning and maintenance) on the heat interface unit
requires specialist knowledge. In general, only authorised specialist
tradesmen are allowed to carry out service work on the heat
interface unit.