UNIVIEW OET-213H Скачать руководство пользователя страница 50

Страница: 50 / 97

(3)

Configure IPv6 settings as shown in

in the figure above.

Table7-5

Parameter Description and Configuration

Parameter

Description and Configuration

IPv6 Mode

The default value is

Manual

. Keep the default value here.

IPv6 Address

Enter the IPv6 address of the device.

The IP address of the device must be unique across the network.

Prefix Length

Enter the length of the subnet prefix of the device.

Default Gateway

Enter the default gateway of the device.

(4)

Set parameters as shown in

in the figure above.

Table7-6

Parameter Description and Configuration

Parameter

Description and Configuration

MTU

The value ranges from 576 to 1500.

This parameter is not displayed when

Obtain IP Address

is set to

PPPoE

Port Type

The default value is

FE Port

. Keep the default value.

Operating Mode

The options are as follows:

10M Half Duplex

10M Full Duplex

10M Auto-Negotiation

100M Half Duplex

100M Full Duplex

100M Auto-Negotiation

Auto-Negotiation

(5)

Click

Save

to complete the configuration.

4. Time

Users can try the following methods to adjust the system time of the face recognition terminal to correct time.

(1)

Choose

Setup

Common

Time

to go to the

Time

interface.

Figure7-17

Time Configuration Interface

Table7-7

Parameter Description and Configuration

Parameter

Description and Configuration

Sync Mode

The options are as follows:

Содержание OET-213H


































































































Результаты поиска

Содержание OET-213H

Отзывы:

Бренды по названию

Популярные бренды

UNIVIEW OET-213H, Руководство пользователя

Результаты поиска

Содержание OET-213H

Отзывы:

Бренды по названию

Популярные бренды