Ultrasonic UP3218 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 272

background image

Property of Ultrasonic Power Corporation -

© 2018

Publication #181114

96

When first learning the capabilities of this system, do no leave

items

unattended  in  the  wash  tank  for  long  periods.  The  system  may  damage
surfaces  if  allowed  to  remain  in  the  ultrasonic  bath  for  extended  periods  of
time.    Longer  cleaning  times  can  be  used  after  thorough  testing  has  been
completed.

Do  not  place  items  to  be  cleaned  directly  on  the  tank  bottom.  The  bottom  is
essentially  a  high  frequency  speaker  so  contact  may  hinder  the  acoustic
propagation.  Use  UPC  approved  baskets  or  fixtures  that  are  designed  to  minimize
acoustical  losses  and  or  damage  to  the  tank  bottom  and  the  transducers.  Heavy
items should always be suspended or placed on a work rest.  In cases when a work
rest is required, consult UPC regarding a proper design for your application.

Do not attempt to clean aluminum in a caustic solution.
Do not use any chemical that is combustible. Chemicals not approved by UPC may
void warranty. Consult with UPC if unsure.
Do not use bleach or ammonia as a cleaning chemical.

2.4. At the End of Each Day

1. Turn filter system to the

"ON"

position. Allow the filter system to clean the water-

detergent solution. (Note: Operating the filter system during the cleaning cycle
may interfere with the ultrasonic cleaning process. If filtration is required during
the cleaning process, use the lowest flow rate possible for maximum
performance.) Make sure that the external valve is opened to allow for proper
flow.

2. Turn filter system to the

"OFF"

position (if applicable).

3. Turn the heater switch to the

"OFF"

position.

4. Turn the main power switch to the

"OFF"

position.

5. Wipe off the machine to remove excess dirt and water.

«
...
94
95
96
97
98
...
»

Содержание UP3218

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UP3218

Бренд: UnionSpecial Страницы: 56

Бренд: K&K Страницы: 8

Бренд: Quincy lab Страницы: 4

Бренд: AcceleDent Страницы: 3

Бренд: Zero 88 Страницы: 32

Бренд: Campbell Страницы: 2

Бренд: Olympus Страницы: 56

Бренд: SandenVendo Страницы: 19

Бренд: JBM Страницы: 12

Aristo WeldCloud Mig U5000i

Бренд: ESAB Страницы: 28

Бренд: Joyolight Страницы: 4

SynCore RW Unit

Бренд: Ridder Страницы: 28

Бренд: Asaklitt Страницы: 5

Бренд: halstrup-walcher Страницы: 47

Turbo Jet 10 i-CON

Бренд: Stocks AG Страницы: 30

Randell DROP-IN 9550-290

Бренд: Unified Brands Страницы: 16

Бренд: E-LINK Страницы: 4

Бренд: SaMASZ Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды