Ultrasonic UP3218 Скачать руководство пользователя страница 86

Страница: 86 / 272

Property of Ultrasonic Power Corporation -

Publication #181114

5. Component Repair and Replacement

Only trained personnel are allowed into the inside of the machine.

5.1. GENERAL

This section includes instructions for the adjustment, disassembly, repair and

replacement of selected components. Illustrations showing the various parts and

assemblies referred to in this Section are in Section 6.

WARNING: EXTREMELY HIGH VOLTAGES, WHICH CAN CAUSE

DEATH ON CONTACT, ARE PRESENT IN ELECTRICAL CIRCUITS OF

THE ULTRASONIC SYSTEM. ALWAYS USE THE FOLLOWING

PRECAUTIONS WHEN WORKING ON THE EQUIPMENT:

1. NEVER REACH ACROSS A SYSTEM WHICH HAS NOT BEEN

TURNED OFF, THE PLUG PULLED AND THE HIGH-VOLTAGE

CAPACITORS DISCHARGED.

2. WHEN SERVICING LIVE ELECTRONIC EQUIPMENT, ALWAYS

WORK WITH ONE HAND IN YOUR POCKET OR BEHIND YOUR

BACK AND STAND ON AN INSULATED PAD (e.g. RUBBER).

THAT WAY, IF YOU DO GET SHOCKED, THE CURRENT WILL

NOT PASS THROUGH YOUR BODY.

3. DON'T CARRY ON CONVERSATION OR PERMIT YOURSELF TO

BE DISTRACTED IN ANY MANNER WHILE SERVICING LIVE

EQUIPMENT.

4. NEVER SERVICE LIVE EQUIPMENT UNLESS SOMEONE IS IN

THE SAME ROOM WITH YOU.

5. NEVER TURN OFF THE MAIN POWER SWITCH IN SOME

REMOTE SPOT AND THE SERVICE EQUIPMENT WITHOUT

ALSO PULLING PLUG ON LINE CORD.

6. IN THE EVENT OF SHOCK, ARTIFICIAL RESPIRATION SHOULD

BE APPLIED IMMEDIATELY. IF POSSIBLE, BY A PERSON

TRAINED IN ADMINISTERING SUCH TREATMENT.

Содержание UP3218

















































































































































































































































































Результаты поиска

Содержание UP3218

Отзывы:

Ultrasonic UP3218, Руководство оператора и по техническому обслуживанию, Страница: 86 / 272

Результаты поиска

Содержание UP3218

Отзывы: