Ultrasonic UP3218 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 272

background image

Property of Ultrasonic Power Corporation -

© 2018

Publication #181114

44

4.

Adding Chemicals

– Use the mixture rate recommended by the detergent

manufacturer.  After  cleaning  one  or  two  items,  you  may  choose  to  increase  the
chemical ratio. The amount of chemical will be based on the condition of the water
being  used  and  how  much  contamination  is  to  be  removed.    Detergents  that  are
used  in  this  ultrasonic  cleaning  system  must  be  compatible  with  304  and  316L
stainless  steel.

You will void the warranty if chemical attack to the stainless

steel occurs.

5.

Power On

– Turn on the ultrasonic start switch. The ultrasonic generators will start

the ultrasonic action in the tank. All installed generator circuits are controlled by one
switch on the control panel. The power intensity should be set to 80% and adjusted
after testing parts. If UPC performed a cleaning test, consult the test report or
contact your sales representative.

6.

System Degassing

-

If new water and detergent has been added allow the system

to  run  through  one  cycle.  This  allows  the  water  in  the  cleaning  tank  to  properly
degas  (the  water  comes  to  oxygen  equilibrium).  The  de-gassing  process  removes
unwanted  air  molecules  from  the  cleaning  tank,  thus  maximizing  the  efficiency  of
the cavitation/cleaning process.

7.

Liquid Overtemp Protection

– The liquid overtemp protection’s primary purpose is

to turn off the system when operated

above 180˚F. When the system is operated

above 180˚F, liquid overtemp indicator will turn on. Liquid overtemp indicator will
stay on until the system reaches below the pre-set (Pre-

set at 180˚F) temperature.

Contact UPC if system does not turn on when temperature reaches below the pre-
set temperature.

8.

Pump and filter system -

The pump and filter system’s primary purpose is to filter

out  contaminants  from  the  liquid,  extending  the  life  of  the  detergent  which  lowers
operating  costs.  However,  agitation  in  an  ultrasonic  environment  will  hinder
cavitation  so for  optimum  performance,  it  is recommended  that  the  operator either
not  use  the  pump  and  filter  during  cleaning  or  set  the  flow  rate  to  the  lowest  rate
permissible. Some users will operate the system at 100% between cleaning cycles
or work shifts.

9.

Sparger and Weir System

–

The sparger and weir system’s primary purpose is to

remove  floating  contaminants  from  the  surface  and  prevent  them  from  being
redistributed  back  into  the  system  tank.  Reservoir  (weir)  tank  is  fitted  with  an
overflow  fitting  and  can  be  drained  independently  of  the  system  tank  in  order  to
maximize the life of the cleaning fluid.

«
...
42
43
44
45
46
...
»

Содержание UP3218

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UP3218

Бренд: Parr Instrument Страницы: 24

Бренд: JBL Страницы: 15

Бренд: Zenbooth Страницы: 60

Бренд: Nektar Страницы: 3

Бренд: Youkey Страницы: 86

Бренд: Wacker Neuson Страницы: 62

Бренд: JB-Lighting Страницы: 32

Бренд: W&H Страницы: 72

Бренд: Vapotherm Страницы: 32

Бренд: Vanguard Instruments Страницы: 47

Бренд: Yamaha Страницы: 48

Pendalyte 40472U

Бренд: Lightolier Страницы: 3

Бренд: KAM Страницы: 5

Бренд: ABB Страницы: 106

UG 2200 Special

Бренд: Amazone Страницы: 252

Бренд: HOFFEN Страницы: 22

Бренд: KEP Страницы: 33

Бренд: Focal Meditech Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды